Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
EDIT: We found the reason for this and it is a hardware issue. This question can be deleted as it is no longer valid.
-----
Hello,
We are currently developing a...
Hello,
I would like to obtain some information on the possible substitutes for the nRF51822 (BGA Packaging).
I received notification that right now only the final orders...
I am using the nrf9160 for an OTA firmware update application. I initially executed the fota download file from the http_application_update sample project in it's default...
Hi,
I am currently running a custom bootloader I found that updates via SPI. I have 2 nrf52840 DKs that are programmed as an SPI master and a SPI bootloader. I have been...
After developing with an nRF52 832 DK (pca10040), our code builds and runs fine. But when we try to use the same code on the nRF52840 dongle it does'nt work. We added flashing...
periodic_adv sample is not working with nrf5340dk_nrf5340_cpuapp
it is working for nrf52840dk_nrf52840 after adding CONFIG_BT_LL_SW_SPLIT=y to proj.conf
Here is the log...
My problem is the that on some devices the ScanResult.getDevice() or ScanResult.getScanResult() both return null on some devices but works fine on most.
This is probably...
Hi folks,
I want to calculate the timestamp for which my thingy 52 board was scanning from another thingy 52(may be more than one board). Is there any technique to get the...
I am confirming ADC sampling 420Hz operation by following question.
https://devzone.nordicsemi.com/f/nordic-q-a/69096/1khz-or-more-adc-sampling-rate-over-ble
The source...
Hello,
I am using the nrf9160DK and I am implementing on zephyr.
For my application I need to write to an external flash memory through I2C. I need to write one page at...
Hello
We are using the NINA-B1 on one of our products.
The phone application is working 100% and was very easy to setup.
Till we came to connect our frontend to...
Hi:
we set p21 as Hardware Reset Pin by config UICR.PSELRESET[0] = UICR. PSELRESET[0] = 21
when we use these code to check halt state, but always get DBG_HCSR zero value...
Hello,
I am attempting to install the nRF Connect SDK v1.5 on a Mac Mini with Mac OS 11 with Apple M1 Silicon per the instructions:
https://developer.nordicsemi.com/nRF_Connect_SDK...
We are using the Nordic fork of Zephyr on nRF5340.
Looking at the serial interface peripherals (SPI/I2C/UART), we understand that these have shared resources and only one...
When uploading programs to the nRF24 chip, is there a "single memory space" or is there a "bootloader-only memory space" and a seperate program memory space? or is it all...
Hi All
I am using S130, nRF51822, SDK12, My RTC1 compare events is connected by PPI to ADC, I have set it to generate an adc_ppi_event_handler after 6 consecutive compare...
Hello Team,
First Thanks to all Nordic support:)
My problem :
I have interfaced SGTL5000 with Nrf52832 (used SDK 16) I'm getting the audio data on aux connector and...
