Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
Hi all,
I'm new to embedded programing with Nordic I'm using the evaluation of Fanstel EV-BC 805M. I was trying to program the basic program for blinky led, however by the...
Hi,
General information:
nRF52840 SoC
Our own PCB’s with inverted F-antenna
nRF Connect SDK v1.8.0
We are in the middle of approval testing our product. We have...
Dear all,
My application is build on nrf52, nrf connect SDK v2.0.0.
For energy saving purpose, I put the nrf52 into sleep mode, using these code
And wake up via GPIOs...
Hi,
I need to transmit and recieve data over the 2.4GHz radio. I have customized packets to be sent and received over the radio. But I dont want to use ESB or Gazell protocols...
Hello there,
I want to use the nrf52-DK with pc_ble_driver_py. According to the 52832 compatibility matix ( link ) , Revision 3 of the soc needs S132SD v6.1.1 at least....
Hello,
We have developped a product with the nRF52832. Basically, it is a power sensor that uses both BLE (advertising) and ANT+ to send data regularly to a display (third...
Hello, I have a question about the scan request event.
I checked the logs of BLE_GAP_EVT_SCAN_REQ_REPORT. If this event is received, does Softdevice recognize the packet...
What a pity ncs ota not support single bank, but old nrf sdk support.
I know mcuboot not support transfer image over bluetooth, i want to know if there are any other way...
NRF SDK 1.9.1
Modem Firmware 1.3.1
I currently have a production device out in the field that is connecting to a specific cell tower and has the ability to then connect...
hi
I want to use two i2c
But in devicetree add &i2c0 and &i2c1
but it shows undefined reference to `__device_dts_ord_131' and static assertion failed: "/soc/i2c@40004000...
Hi,
I try to advertise nrf52840 dongle on pc to build a connection with nrf5340 uart service. Although I try to modify the advertising program by advertising.py and heart_rate_collector...
Hello there
I need to dynamically initialize and uninitialize the USB HID in my application. Because there is a condition on which I don't want any PC to recognize my device...
Hello there
In the project of the company I work for, we have a device working as a BLE central which connects to a nearby device and checks if that device is registered...
Hello
I'm trying to upgrade to SoftDevice S140 7.3.0 from 6.2.2 but when I program my DK board but it does not work at all. It looks like the application is not even executed...
