I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
Hello, I have problems in the async-mode with the UART21 output and the nRF54L15. I am using Toolchain v3.1.1 and SDK v3.1.1.
When I use the uart_tx function to print out...
Hi
Is there a specification of running the nRF21540 in Tx mode at 10 dBm and 20 dBm with no load connected? Will the reflected signal cause damage to the PA and if yes,...
Hi Support Team
I tested matter bridge sample running on the nRF7002DK with peripheral_lbs sample running on the nRF54L15DK.
Application guide
Then I encountered problems...
I am working with the nRF9160 DK (PCA10090) and would like to use the onboard nRF52840 interface MCU as a host controller for an external peripheral.
From my understanding...
I am using the nPM2100 EK dev board with a stm32wl5MOC.
Using the example from the bare metal drivers, I adapted the code to my board.
I can succesfully read and set bytes...
currently this is more of a theoretical question, but i have an idea of something that might utilize this (3 QSPI devices)
Ive been looking at the Nrf5340 and the nrf7002...
Hi, I am stuck on the BLE channel sounding Initiator initialization. I took the code from the channel sounding connected initiator and integrated into my FW.
Due to unknown...
Hello Nordic Team,
I am using the nRF5340 Audio DK and I want to implement a simple audio loopback — where the board captures voice from the on-board PDM microphone and...
hello~
nPM1304 nominal sleep mode 500nA (it is still uncertain whether the buck converter can operate?)
Can't the sleep mode be lower than 500nA?
best regards
sam
I'm following the Lesson 9, Exercise 2: DFU over USB - Adding External Flash from the Nordic Academy: Tutorial Link
SoC: nrf54l15
SDK version: 3.0.2
Toolchain version...
Hi,
I’m using a custom nRF5340 board , and I recently migrated my project from nRF Connect SDK v2.9.0 to v3.1.1 .
The same project compiled and worked fine on v2.9.0,...
Hello,
I'm interested in nRF54L10 SoC, in Mouser and DigiKey I see that I can buy it in this package: QFN48 (QFAA). However in the datasheet it shows this package QFN40...
Hi,
I’m currently working with the nRF54L15 DK using the Channel Sounding Initiator with Ranging Requestor sample from the latest nRF Connect SDK. The setup runs successfully...
Dear nRF experts.
I am using the radio_test sample with SDK3.10
We used radio_test to add UART commands to control the on/off of all GPIOs for pin verification. We found...
