I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
Hi, I used nrfjprog -e to the nRF54L15DK and problem is in Programmer log.txt How to recover nRF54L15DK does we need to update the nRF5340 JLink debugger?
I configured VBUS with a 1500mA limit. In theory, VSYS should deliver something similar to this. The VSYS output is 5V; it powers some LDOs in my project, which consequently...
Hi, I’m trying to generate a PWM signal directly using the nRF5340’s PWM peripheral registers (not using Zephyr’s pwm_dt_spec or driver API).
The LED turns ON correctly...
Hello,
I am trying to adapt the "Interfacing with a sensor over SPI" example from the nRF Connect SDK Intermediate Dev Academy course in Lesson 5. When I run the code as...
Hello, I am trying to convert my codebase from segger embedded studio to nrf connect. I am currently working on the spi section of my codebase.
I am communicating from...
Since it was brought up in the Webinar today, that the nRF54LM20A is not recommended for use with LE Audio due to the lack of an Audio PLL, I was wondering that the Audio...
Hi Nordic Dev,
We are experiencing issues with sudden connectivity loss and hardlocked devices 1,5 years after product launch. We are currently suspecting the flash storage...
Hello,
I have a Thingy:91x.
I flashed a BLE central program to the nRF5340 on this device.
However, I get an error initializing BLE. I've confirmed that this program...
Board/Setup:
Board: nRF9151 DK / nRF9151 SoC
Peripheral: External BLE module connected via UART1
Use case: BLE module is only needed during commissioning...
Hi there,
I have been trying to implement a low-power mode that basically suspends UART, I2C, etc before entering sys_poweroff() when critical battery level is triggered...
Hi,
I have several field devices using the LTE Link Controller library with nRF Connect SDK v2.5.1. Most of them work fine — they are programed to connect every hour. However...
Greeting Nordic Expert !
I would like to override the following hook in MCUboot:
int boot_perform_update_hook(int img_index, struct image_header *img_head, const struct...
Hello,
In the nRF52840 Product Specification PDF v1.11, on page 836, the second paragraph down states:
" The PSEL.RXD, PSEL.CTS, PSEL.RTS, and PSEL.TXD registers and...
Hello Nordic team,
I’m using the nPM1300 development board to charge a 950 mAh Li-ion battery , and I’ve configured the charger as follows:
Charge current: 800 mA...
Hi,
I'm unable to get the PPKII kit to "connect" to my PC. After selecting the device it just says "Connecting..." forever. Some notes: - When first connecting the kit...
