I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Our device connects to a cell tower and then creates a socket to our gateway. I monitor +CEREG to see what it goes through to connect to a cell tower. Below is the meaning...
I testing UART0 data transmossion. But, could resolve why CPU resets when executing : if (!nrfx_is_in_ram(buf)) in uart_nrfx_uarte.c file. See atached image, where Reset occurs...
I am developing a custom board with an electronic paper device (EPD) attached, which will be controlled with SPI and a five additional GPIOs (a mixture of inputs and outputs...
Hi Guys,
I have a nRF5340-DK(PCA10095) here and I'm planned to perform some BT-SIG RF testing with it but I can't find the proper hex file for DTM(Direct test mode) setup...
I (think I) have successfully located the code responsible for handling the data received BUT! The code segment:
in app_uart_fifo.c
seem to only receive a paltry 1...
Hello
I want to measure Low power current in nrf52840-DK with System ON mode.
I need to know how much current consumes by nrf52840 SoC while I2C Engine ON, SPI ON, and...
Hi.
I am working with the nrfConnect SDK 1.8.0. I would like to configure the nrf5340 for maximum throughput to work as a server for a smartphone device.
How should...
Hi all,
I am using NRF52840 and I am saving some data to the flash memory using fds. The data are 216 bytes in each file and there are 3400 files which is in total 734kbytes...
Hi,
In my application, I am writing in flash.
But when I do so, my openthread data in flash gets o verwritten, the node doesn't retain its commissioning data.
In nrf_SDK_For_Thread_and_Zigbee...
Hi All ,
I am using nrf9160Dk ,When i use asset tracker V2 i successfully get the GPS values on the nrf Cloud . But when i use the Asset Tracker only then i am unable to...
Hi there,
From the product specification of the nrf5340, we can only find UARTE peripherals (UART with EasyDMA). Is it possible to implement uart without DMA? Of course...
Hi
I was just curious as to whether or not there is a specific reason the Xenon's PWM capabilities are not available with NCS/Zephyr. Is there a hard limitation or is this...
Hi Team,
SDK - 17.1.0
chip -nrf52810
I want to store sensor data (12 bytes) every 30 seconds in flash memory. Once the flash is full, I want to replace the old data...
I'm trying to interface with the ds1339 real time clock to set and read the time for timestamping tasks in ncs 1.8.0. I've found a few tutorials that boil down to:
1....
