Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
I am using nRF 5 SDK v 14.2.0. I would like to receive data from smartphones via Bluetooth communication, How do I program? I would like to have a professor. Sorry to trouble...
Hello,
i want to use Seggers RTT on os X (nrf52832). I followed the Tutorial and i compiled and upload with success. But if i start JLinkRTTClient on my mac nothing happens...
Hi
I'm looking for a Dev Kit that replaces the nRF51822 kit in the link below.
https://www.digikey.co.uk/en/product-highlight/n/nordic-semi/nrf51822-bluetooth-smart...
Hello,
We are trying to read a received RSSI value from bluetooth mesh opcode handler however it does not relay this value to the callback.
Callback is added here...
Hi,
I just got a nRF 5340DK (PCA10095, 1.0.0 2021.9) which doesn't show up on my windows 10 computer.
When I connect it to my computer, the green Led 5 blinks rapidly...
Hello! I am a beginner at nrf programming and have just started using the NCS and Zephyr on an nrf5340 evaluation board. I understand that Zephyr seems to be more or less...
I'm using a nrf52810 with limited flash size especially after adding a UART bootloader DFU and S112. I added uECC for connecting security. Now I need AES128 for my own application...
Hi,
I'd need some information I'm not able to find in product specification v1.3:
What is the architecture of the GPIO / AN pins of this device? Input p rotection diodes...
Hello,
I have successfully programmed the ble_app_uart example to a custom PCB using the 52832. Here is the board schematic, on the board C15 and C16 are not fitted.
...
Hi,
I want to know is Liniux system supported Nordic BLE OTA DFU ? According to official documents： https://www.nordicsemi.com/Products/Development-tools/nRF-Util ，it just...
Hello community,
I am implementing BLE peripheral code contains, A custom service, characteristic.
I am referring this link : github.com/.../custom_ble_service_example...
Hello, nrf5340 datasheet -> nRF5340_OPS_v0.5
section: 7.1.26.7 Sending custom instructions (Page: 383) 1. we can send an instruction consisting of a one-byte opcode and...
I kind off trying enable TWI in bootloader mode, This is because of following reasons.
Firmware is stuck in bootloader, if somebody removes the Device Battery during...
Hi.
I'm trying to run an application using a custom SPM module in a nRF5340 where I get an error while running it. I'm using nRF Connect SDK. The terminal gives me this...
