SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
I have trouble getting NFC-pairing to work in nRF52840 running SoftDevice 7.2 based on SDK 7.0.2. The observed behaviour is that the NFC Field is detected but nothing more...
Hi,
I add a new service about DFU of my FW，so three was a problem when it go into "ble_nus_init()" will return NRF_ERROR_NO_MEM, I have read serveral tickets about the same...
i have used "BLE_GAP_PHY_AUTO" in scanner code
actually it should scan "phy coded" and "non phy coded" aid values .
but in my case getting i was getting both "phy coded...
I have a project to use NRF52810 to connect the App. When testing it, I found that when it was successfully connected to the NRF Connect tool, it would automatically disconnect...
Hi, Dev Zone.
thanks for help : )
I'm try to porting DK Board's Ble Bonding function to Target Board.
1st_question <- this is my first question links
main problem...
I'm using
SDK : nRF5_SDK_17.0.2
Example Project : ble_app_uart
Soft device :S113
The initial project builds successfully.
My project has requirements for tow...
development tool : Segger Embedded Studio
SDK:nRF5_SDK_17.0.2_d674dde
it always takes long time to build project
build log:
Building ‘blinky_pca10056’ from solution...
Hello all,
I am developing an application from the ble_cgms example on the nrf5_sdk 17 using the Softdevice S132.
I have implemented a gpiote interrupt whenever the state...
Hello,
I just received nRF9160DK(PCA10090, 0.8.3)
I followed nRF9160_DK_Getting_Started_Guide doc.
But, I hare some issue to activate iBasis Sim card.
It keeps...
Hello, I am using the latest version of pc-ble-driver combined with a pca10040 and I am attempting to write large data packets (200 bytes) to a peripheral. I compiled the...
Hi,
I have tested FOTA code in nRF52840 DK and it works perfect but i have custom board build with nrf52840 when i implement the code it doesn't get start
custom board...
I don't have time to learn the massive API for nRF52840 so I am hoping someone can provide a small
snippet of code (and instructions to put on the dongle) to do the following...
Hello
While converting from nRF52832 to nRF52810, we found a problem that the SEGGER compiler returns with the message
section '.init' will not fit in region 'UNPLACED_SECTIONS...
Bluetooth didn't have a standard for transmitting audio using LE until LE Audio was released. And many manufacturers which produced BLE remote controls used Voice Over HID...
In my project, nrf9160 has to send and receive data from the I2C bus from a chip. Everything works fine but unfortunately I have to query the chip by sending a single byte...
