Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi.
I am developing with NCS 2.7.0 using 5340 and have configured it to use 5 generic switches. These work fine. However, the order of the switches displayed in "Home" on...
Hello,
Used environment:
Board: nrf9151dk_nrf9151_ns
SDK Toolchain: v3.0.2
IDE: Vscode
I'm trying to test the LIS2DH sample using the nrf9151DK and the STEVAL...
Hi all
I have a project that I developed with SDK 17.0.2 in Segger Embedded Studio. It works well, but now I would like to add a GitHub Runner to compile it every time I...
I can't write the Blinky app I created in lesson 1 excersie 2 to the Thingy 91. This is the log:
21:09:41.574
Initialising the bundled nrfutil device
21:09:41...
Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
Hi,
We're currently evaluating the cellular capabilities of the nRF91 modem using the nRF9151 DK. We've encountered issues with roaming: when the devkit is taken to another...
I have an Ubuntu Machine where I successfully installed Zephyr SDK and toolchain following instructions given in the official getting started guide here . I was able to compile...
None of the examples in the SDK are useable in Visual Studio Code. All are missing the required application source files
Get this error
The directory "c:\Users\mtd18\...
I used the "echo_bot sample and tried to alter it to use UART2 instead of UART0. Aftet changing the code and putting in the needed overlay, the main() program begins to run...
Hello Team,
I am currently using the nRF54L15 DK with NCS version 2.9.0 for development and compiling code for the nRF54L10 board.
I am trying to implement FOTA updates...
I'm transitioning a GNSS tracking firmware from the nRF9151DK to my custom board using SDK/toolchain v3.0.2.. On the DK, I get accurate location fixes, but on the custom board...
Hi,
I fiddled around with examples using the PSA API to compute a MAC by AES-128 CMAC. That worked out fine. I can import a key, use it to compute the mac over a message...
Hi, On the nrf54L15 with MCU boot enabled, what is approximately the fastest time that the chip could boot and set a gpio line high, if everything not critical is disabled...
