I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I am using nRF52840 Preview DK (0.12.0) and I want to measure USB currents. I am using the DK as a starting point for doing measurements on custom HW and verifying that we...
I can program and debug using Segger Embedded Studio v4.12 on my mac without a problem. When I try to use the command line to program and erase a nrf52840, I receive the following...
Hi All.
Practising Secure DFU, my nRF52840 DK board seems like if it is locked. Only Leds 1 and 2 are ON. The board is advertising with DEVICE_NAME=Dfu Targ and its COM...
Hi,
I would like to know the correct way to change the polarity of the CS line for SPI devices. The SHARP memory display is opposite of most SPI slave devices so I need...
Hi, I am using the nRF5_SDK_14.0.0_3bcc1f7 with SD v5.0.0 and the ble_app_beacon example together with the Jlink Monitor mode for debugging. The issue is that under some circumstances...
Hi,
I m using now two thingy and I m looking for the possibility to compute the difference between the two accelerometer to determinate the the moment of one compared to...
I'm trying to get back into the swing of bluetooth development, and right now I'm trying to find an overall ladder/timing diagram for a full bluetooth/softdevice transaction...
Is model Publish Retransmit (Mesh Spec 4.2.2.6 and 4.2.2.7) currently implemented in the Mesh SDK? I noticed that with Publish Retransmit Count set to 1, the Zephyr Mesh stack...
In nrf52832 datasheet, it uses" 64 MHz crystal oscillator, using external 32 MHz crystal "
then, can I use external 16 MHz crystal or external 4 MHz crystal to drive nrf52832...
I couldn't find nrf_drv_timer.c file. I want to create timer so I try to different SDK for my work. I am using SEGGER IDE for prepare software but i encountered lots of problems...
Dear nordic,
I try to build BLE application everything works fine expect the UART. The UART has transmission issue.
it has no problem in receiving. but when i tried...
Hi,
I am using nrfMesh2.2 SDK. I want to add models other than GenericOnOff and configurationclient to the interactive_pyaci. How do we proceed with this?
I found the utility to create the binary image of the production data for my Zigbee device but cannot find any documentation on how to incorporate the generated BIN file into...
Hi,
I have a custom board with nRF52832 and I'm using SDK 13.1 and softdevice s132 4.0.5. I have a GPRS module that I will use to receive the new firmware image and I will...
Dear Nordic,
I installed nrfConnect 2.6.1 and lauched "BluetoothLow Energy" application. Then i selected my board and it asked "Device must be programmed ..." and loaded...
