This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
I have the problem that I am currently unable to debug any of my Bluetooth applications.
I'm sure that I was able to do this without any problems during the original development...
Hi,
I am currently working on communicating between the nRF5340 DK and the nRF5340 Audio DK over BLE. Could you please share the information flow?
Warm regards, Rajendra...
Hello everyone.
I am going to do a project recently. We are using dht22 to transmit temperature and humidity, and use temperature values to control LEDs.
This project...
Hi,
I am working on a project which has external flash (FM25V01A ) connected to nrf52832 board over SPI. And when building the project, I am getting the following error...
On the nRF51, LO leakage was measured when in receive mode. For 2402~2480mhz, LO leakage was measured at approximately 2745~2836mhz. The nRF52 does not measure LO leakage...
This is driving me totally nuts. There are inconsistent pieces of information in documents and code. I am getting a modem reset loop problem. The documentation says the timer...
WE are using IM66D130A (digital mic) and nrf5340 on our custom board. The mic picks up the heart beats which we need to transfer to the mobile application in real time. The...
For a device like the nRF9160 Feather, you need a second USB to UART device for listening to the modem traces. When I go to select the Terminal Serial Port under Advanced...
Hello,
I'm trying to do an HTTP multipart POST with chunked transfer encoding but am having trouble sending the headers to the socket. When trying to send, I receive a ...
Hi,
I am currently migrating from NCS 2.5.0 to 2.7.0 and running into an issue where the CMakeLists of mcuboot ( https://github.com/nrfconnect/sdk-mcuboot/blob/4c7942e58c5458ce3c4e50d3169e0f865910fe87...
Hi,
Long story short, I made some boards using nrf9160 modules, received parts from DigiKey, soldered but can't make them work, at all.
nReset pin is stuck low. Tried...
I am using nRF52832 for high-rate sensor.
Of course, I can use SPI using CPU but it's busy for other jobs.
So I want to use DMA if it's possible.
Currently I am using...
I've got a project based on NCS v2.6.0 using a nRF52840 as contained in a Fanstel BT840F module.
With help from you all (thank you!), the software works. Bluetooth and PWM...
I am using the nRF5340 and trying to get MCUBoot working. I am running into problems and looks like I need to edit the MCUBoot code, the problems are long and numerous too...
Hello,
We're seeing an error that only happens after a cold reboot (unplugging the battery and replugging it) and it happens inside the bootloader while trying to open the...