I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
I am using nRF Connect fro Desktop Bluetooth Low Energy Standalone v4.0.4 with a Dongle USB nRF52840.
I can see my device when Legacy Advertising is enabled, but if I only...
Hi,
First of all, let me confess, I am new to VS Code - NRF SDK environment.
I have a VS Code setup with NRF extensions enabled and due to some reason, the error squiggles...
Hi , I 'm trying to send and receive on a websocket. Sending works fine and is received on the backend, but when I try to receive I just get garbage in my buffer.
I sanity...
Hi,
I'm currently trying to add MCUBoot in my project.
The project was built successfully by adding these lines to prj.conf.
CONFIG_BOOTLOADER_MCUBOOT=y
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU...
I'm looking into using command line builds for nRF Connect SDK again due to issues I've been running into with vscode.
The instructions on this page ( https://docs.nordicsemi...
I have tried zephyr/sample/bluetooth/periodic_sync_conn in nrfsdk v2.7 and test on nrf5340 audio dk, and doens't work. the output is:
*** Using Zephyr OS v3.6.99-100befc70c74...
Hi,
How to solve the problem of writing data to flash using the write_data_flash function in save_stack_data function
1.1. I tried to add the function save_stack_data...
Hi! Background (feel free to skip) --------------------------------------- We have 3 nRF52840 boards, connected via ble/NUS as follows:
B also advertises bluetooth HID...
Hi, we are using the nRF9160 in conjunction with the nPM1300. To power off the device, we call lte_lc_power_off() which sends the AT+CFUN=0 command to the modem and waits...
the v2.7.0-5cb85570ca43 zephyr/ndk combination doesn’t work for things using the JSON_TOK_FLOAT type (vs the number type). this is because zephyr/lib/utils/json.c:float_ascii_encode...
I am working on a project in which i have got 100 nodes we are doing it in our custom board. so i need to assign unicast address manaully for each nodes inside it. How can...
When I try to build any application with west I always get a CMake error complaining that it is unable to run the Python version included with the NCS toolchain. The error...
I'm working with a DVK that has an nrF52840 with a Sierra Wireless HL7800 modem. The modem is connected physically to UART1 while the UART0 is used for the following as shown...
Hello
I am at the early stage of evaluation of a nRF52840 USB Dongle and I have installed all software on my Win 11 PC.
Just trying to check that everything is working...
