Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Hello
We are using a slave processor with AT command to communicate with the nRF9161 . This is working without problem
But we are initially using the Quick Start 0.2.7...
Hello,
I'm using nRF9160 as a HCI host and nRF52840 as HCI controller (nRF52840 config is based on HCI lpuart example). My application receives data over Bluetooth using...
We have two cases where the modem has downgraded itself from version1.3.2 to 1.3.1.
1. In the first case, due to water ingress, it appears that the reset pin has been toggled...
System: Windows 10, Vscode + Nrfconnect
I saw a previous post on same topic which fixes the issue by changing the settings in extension like said here ( changing extension...
We have pre-production product (based similar to the NRF9160dk setup with a NRF9160 (LTE-M, GPS) and a bridged NRF52840 (BLE). We are working through certifications for CSA...
Hi all,
I am aware of the different access port protection mechanisms (listed in my previous ticket here: Link ). I did also test both revisions successfully:
For...
Hi.
In our private network we experience one problem.
We can ping Google (8.8.8.8) via APN customer4. In Wireshark traces it is seen that ping is initiated.
On RRC level...
In our current development we are using NRF52840DK and the external memory MX 25R6435F. We are using Settings API to store some configurations on the external memory partition...
Hi, I have the structure for a Vesper VM3011 MEMS microphone:
In the 'overlay' file, I define it as hardware:
When I retrieve the properties from the '.c' file...
We are currently working on a project that has these requirements:
BLE Audio (Broadcast)
BLE Central and Peripheral
WIFI 5/6 (5gHz and 2.4gHz)
BT classic would be...
Hi,
I am currently developing a long range bluetooth module with the U-Blox NINA-B31 BLE module, based off the Nordic nRF52840 chip. I have come across an issue which I...
So, I have built prototype boards using nrf9160, flashed, they are working fine, now need to add to nrf Cloud and realized there are few ways to do that, all are not well...
Greetings
I am going through the BLE fundamentals course and I am doing exercise 1 of lesson 4, creating a custom service. From this exercise, creating the "LBS" service...
Hello,
For context, I am using an EVK-ANNA-B112 development board which has an nRF52832 inside. The development board has an external 32.768KHz HW clock connected to the...
Hello,
I am using sd_rand_application_bytes_available_get() in nrf_drv_rng_bytes_available()
A first generation of randmon number is made without problem.
But 5...
