I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
i have a "bare-metal" (register-level access) BLE advertising program which does not consistently consume the same amount of power when transmitting.... here's what the power...
Hi,
I had some issue with my nRF52 DK PCA10040 v3.0.3, The programmer was totally unreachable also with the simplest terminal command so I tried to reprogram it trough hidden...
I am trying to implement GPS code in the nrf9160 but I cant find the function nrf_modem_gnss_init(); to initialize GNSS inside the modem in , is it being initialised within...
The following log is a compilation error.Is there any way to correctly compile?
e:/nordic/ncs/toolchains/fd21892d0f/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm-zephyr...
We have an application where response time is critical, and we are trying to minimize the time from advertising to an active channel sounding session.
What we have already...
Dear Nordic,
We are currently evaluating the Amarisoft CallBox as an end-of-line (EoL) testing tool.
In an ideal scenario, we would like to use 1NCE production SIM cards...
When performing FOTA using NCS 2.9.2, we observed that the swap using move process takes approximately tens of seconds. However, with NCS 3.2.4, the same swap using move operation...
nRF Connect SDK v3.2.3, nRF9160.
Hi,
I'm working on a project which has MCUBoot enabled (dual slot) for firmware updates over cellular connection. I did not have a pm_static...
Hello,
I want to program the bare nRF52832 MCU over SWDIO, SWCLK, GND and +3,3V Connections with a Segger J-Link programmer. Unfortunately the programmer could not connect...
We are experiencing an issue with the QSPI driver on nRF54L15 where external flash access stops working after a BLE bonding procedure.
The system works correctly until bonding...
Is it possible to be able to get hold of some of the legacy software for the nRF52 BLE sniffer that works off the old nRF Command Line Tool rather than the nRFutil? As I'm...
Hello together!
I am trying to reproduce the ultra low power connection as described in this whitepaper: /cfs-file/__key/communityserver-discussions-components-files/4/3482...
Hi,
I am working on a smartwatch PoC using the nRF7002 DK (nRF5340), and I am trying to interface a 1.8" ST7735 SPI TFT display (128x160).
Hardware: - Board: nRF7002DK...
Ultrasonic welding is commonly used to seal plastic enclosures for electronic devices. 32kHz crystals can be damaged by this type of welding and manufacturers recommend not...
