Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Currently, I am only powering the NRF5340 chip to test its performance. I have opened a standard example project located in the directory: nrf\samples\bluetooth\peripheral_uart...
Hi, I’m currently working on a setup with three nodes:
Node A : collects data
Node B : acts as a relay, forwarding data
Node C : processes the data and then...
Dear Nordic Team,
I hope this email finds you well.
I am currently working on integrating group functionality with a Matter device (Node ID: 114, Endpoint ID: 1) using...
I was using an SPI serial nor flash device with NCS 2.8.0. I tried to get the flash into deep power down mode, but it doesn't seem to work well with NCS 2.8.0. So I upgraded...
Similar to ticket # 349557, we plan to operate nRF9151 in SLM mode and use both LTE and GNSS features. There is some interest in having GNSS (NMEA) data sent out on a dedicated...
Hi Team,
We have started our BLE development using nRF54L15 using SDK 3.1.0.
We have selected this MCU because it support all security features, we are going to start...
NFC certification and library.
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrfxlib/nfc/README.html tells me, NFC is supported by nrf52 and 53.
e.g. libnfct2t_nrf52...
I am using nrf54l15 with NCS v3.1.0 with the following error when i connect it(i worked in NCS v2.9.1 successfully):
Controller unresponsive, command opcode 0x2035 timeout...
We as a company love the app (nRF Connect) and use it accross a lot of devices to recover stolen goods with BLE.
However, on all my Android devices (modern tablets and phones...
I am working with St7789v driver based RGB565 Display . I have chosen SPI21 configured at 8Mhz and if I send 15 bytes chunk of image bitmaps, I can see the image in the display...
Hello, I am testing the system off demo on the nRF54L15 DK using nRF Connect SDK v2.8.0 (Zephyr v3.7.99). I ran the sample exactly as provided in the SDK .
Observed log...
I am using the nRF7002DK with the nRF5340 SoC. By default the board runs at 1.8 V until I provide 3.3 V on VIOREF. Currently, I am using another board just to drive VIOREF...
Hello there,
we're using multiple pwm-channels of one module of the nRF54L15 for different purposes (multiple motors, h-bridge control; depending on the project).
When...
Can my Power Profiler 2 be faulty?
It does the following in both source meter and ampere meter mode. I start to measure and it shows some microamps current that's expected...
