I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
Hi, I have read the "nRF91 AT Command Reference Guide v0.7" and I would like to propose a new AT command to be added and also an additional feature to an existing AT command...
Dear nordic:
I am confused of NRF51824 MTU issue, NRF51824 can use S130 softdevice, S130 is qualified bluetooth 4.2 core spec, then why S130 features don't included MTU...
While trying to find out a realistic maximum power consumption target I was searching for the power consumption of the LPCOMP comparator. I've seen a few claims about 0.5...
Hello,
I want to send data from central device to peripheral device. I am currently using nRF52DK.
While sending data from peripheral to central device, data is sent successfully...
hello all,
I buy the Fanstel EV-BC832 V2 and start to paying with it.
I used the IAR ide and Embedded studio (SEGGER) ide for my tests.
First i check the blinky and...
I development nRF52832, I want change mac address.
So I modified nRF5_SDK15.0.0/examples/ble_peripheral/ble_app_uart.
I added code to the examples.
////////////////...
Hi everyone,
I want to program the nrf51822 module with the discovery board stm32f429i-disc1 through ST-LINK programmer in Keil IDE but this error appears: "ST-LINK connection...
Dear DevZone Team,
I am an absolute beginner in the field of mesh networking and hope you could help me getting started. Please bear with me.
I have a bunch of sensors...
Does anyone uses Sloeber to program nRF52? I have an issue, when I add a header nrf_temp.h to the project and using following functions:
The problem appears when I add...
Dear Nordic team,
We are developing a BLE application for IOS and Android. On Android, we utilized your Nordic Scanner Lib to scan Bluetooth devices and it is fine and...
Hi. I am trying to stop advertising after a delay in the UART example using;
sd_ble_gap_adv_stop(???)
What do I put in the brackets? It is asking for a uint8_t called...
Hi,
How to stop freeRTOS xtask using timer and recreate again when needed? I'm currently want to control the blink interval, for example I want to have the led blink for...
I used sdk15.2.
The peripheral sends the public key to the central.I received an exception to public key processing.
code:
case BLE_BITBUTTON_C_EVT_BITBOTTON_M_NOTIFICATION...
Hello Everyone,
Struggling with evaluation of Secure DFU over UART lines. I used the sample project "Secure DFU Bootloader over Serial Link (UART/USB) ", during the previous...
