Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Question preamble
I am writing a bluetooth application where two nRF5 devices will be in a master / slave configuration. However, I want to be able to flick a physical...
Hi.
I have an application that needs a low security encryption. Therefore I want to use "Just works" encryption. The pairing process is assumed to be in a "safe" place...
I am having a strange problem. After I flash the program to the NRF52 and do a reset (does not matter whether it is a soft reset or pin reset) the system (DK and my own board...
Hi,
i read this post:
devzone.nordicsemi.com/.../
and found the PCA20006 project but i cannot load it to the beacon. I can find proper instructions on how to load...
I had initially added ble_dfu buttonless DFU support (unbonded) to my app per instructions here: infocenter.nordicsemi.com/.../service_dfu.html
Long story short, based...
What unique information can I use to know which physical device disconnected for example? Say I have a MAC address or a name encoded into the advertising packet. Correct me...
Here the connect method is called
err_code =
sd_ble_gap_connect(
peer_addr,
&m_scan_params,
&m_connection_param,
APP_BLE_CONN_CFG_TAG);
In the ble event...
I'm tring to connect my phone to the multi-connect example client app
I'm tracing the ble events in the ble_evt_handler.
When I open the server app on my phone, I see...
Hi Engineers!
faced with a problem of SAADC impedance too small (4,7K)!
We use SINGLE ENDING 8bit mode with following settings:
NRF_SAADC_REFERENCE_VDD4
NRF_SAADC_GAIN1_4...
We are moving from a PCB using a nRF51822 QFAB module to a newer PCB using an nRF51822 QFAC module.
We observed that with the new QFAC PCB we have a significant connection...
I want to use the nrf52dk PCA10040 to remote program a BC832 chip from Fastel.
They say:
"BC832 V1 pin B3 C3 (DCC, DEC4) needs to be connected to the program can be burned...
I have an nrf52832 BLE HIDS device based, with the connection and peer handling code copied from the hids keyboard example, SDK13. I use Windows 10 as host. Setting up a connection...
I plan to keep the bonded device information in the ring buffer, but there are a few things that puzzled me:
When PM_EVT_CONN_SEC_CONFIG_REQ event is received, .allow_repairing...
Hi,
i am working ANCS example project in nrf14.1.0 SDK, s132.5.0.0 softdevice. i am able to print category of all notifications. i wanted print text message info. is it possible...
