What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello,
As nordic has implemented sdk for mesh and i have been using mesh sdk v3.0.0 LIGHT_SWITCH_EXAMPLE but i am facing some problem regarding pa_lna. Actually wt i have...
Hi,
I am testing my I2C function by using ".examples\peripheral\twi_sensor" of SDK 15.2.
Because my SDA and SCL is define in P0.04 and P0.02, and my I2C Slave is MPU6050...
Hello,
I would like to know that what are the provisioning parameters needed to add an Unprovisioned device into a mesh network?
Thanks and regards,
Jahnvi.
We, I am using nRF 5 SDK v 14.2.0.
This time, without using WDT, using only the application timer, We are developing a process to send data by detecting acceleration and...
Hi,
I'm currently trying to implement Peer Manager in my existing project, for both pairing and bonding. I'm using the ble_app_template in examples/ble_peripheral in the...
Is it possible to use the TWIM and TWIS at the same time with 2 different I2C buses with openthread.
I tried this with THREAD SDK 1.1 and had link problems because of the...
Hi, I'm trying to setup attribute reporting on zigbee HA, the device role is ZB_ZCL_CLUSTER_SERVER_ROLE, I want to configure reporting for cluster 0x0006, so each time I flip...
SDK v14.0, SD132 v5.0.0
We're creating and starting app_timer instances before we enable SoftDevice via nrf_sdh_enable_request(). It seems to work, but I remember that...
Hello,
Is Bluetooth 5, capable to communicate with BLE devices as well as classical BT devices? I think this dual capability is called smart ready.
We are planning to...
Hi,
I can program our old Nrf24LE1 boards with Nrfgo Studio, but when I tried using Nrfgocli command it fails to connect to
the board. My motherboard is set to number...
I noticed that CMSIS Configuration wizard expects values in HEX and converts them into decimal in the sdk_config.h file.
e.g. for SEGGER_RTT_CONFIG_BUFFER_SIZE_UP. I entered...
Hello there, I am using nrf52840 The mark is: N52840 QIAAC0, SDK: nRF5_SDK_15.0.0_a53641a, SD: nRF5_SDK_15.0.0_a53641a, I used the BLE ANCS routine and encountered this problem...
Hello,
We have a custom board based on nRF52832. The problem is that when trying to run basic example Blinky (examples\ble_peripheral\ble_app_blinky\pca10040\s132\arm5_no_packs...
Timer interrupt does not work well. In the code below, LED doesn't turn off and "interrupt!" message is not received. I really appreciate it if you give me any advice.
Hi Everyone,
I want to make a program code to establish the connection between MCU(nrf52832 chip) and accelerometer.
What are the conditions required? and i need some...
