SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
I' m using custom board of nrf5340 with nrf7002, and the SDK version is ncs v2.5.2.
I've tried to build and run, but the log in RTT viewer is only print the line "Bringing...
On the nRF51, LO leakage was measured when in receive mode. For 2402~2480mhz, LO leakage was measured at approximately 2745~2836mhz. The nRF52 does not measure LO leakage...
OK, I'm working with the nRF52832 and NCS V2.6.0, and I have two different actions I need to complete at various times with the SAADC:
Every ~ 3 seconds, I need to sample...
Hi,
I have 2 nrf52840-preview dk board. All of a sudden both the devices are not working any more.
I have referred to some suggestions and tried all the below cases and...
Hi,
I'm running some transceiver tests to look at extended broadcast and ISO transfer modes. I am using nrf5340_audio_dk and ncs V2.6.0 to run nrf5340_audio application...
When i try to run or debug the ble app uart example on our own hardware using the nrf52810 there is a fatal error when executing the code.
The example does run on the...
i Used a nrf52840 DK board and zephyr sdk v2.6.0. I'm start the ble advertisement and configure the gpio interrupt on sw1 in low mode flag GPIO_INT_LEVEL_INACTIVE (Low level...
I want to use RTC in my project. I'm facing build issue (undefined reference to `__device_dts_ord_113') in my project .
STEPS TAKEN: 1. I have enabled the RTC configuration...
I'm developing with ncs v2.6.0 in the board that made by myself with nrf52832 mcu.
I start a new project with copy from nrf_dm sample.
In my board,just one LED used and...
Good Day
We have an issue where our device will run normally in a full load condition for about 2 hours without issues but will suddenly go into the app_error_fault_handler...
Hello, I am wondering - Is it possible to program BL651 Bluetooth 5 with nRF52810 using pca10040 development board with nRF52832 on it and using
BLE HID Keyboard and Mouse...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I'm studying the CDC_ACM...
Hello, I am going through the Bluetooth Low Energy Fundamentals provided by Nordic.
My nrf 52840 dk could function fine after lesson1, but when I flash my board with the...
Hello
I am using nrf5340 raytak board which does not use DC_DC power, uses internal quartz. When I play the Bluetooth peripheral example I get the following error(I using...