Hi,
I am sending data from Android phone in every 200 ms to nRF8001. But sometimes I found there is a 50 ms or 100 ms delay. It looks like nRF8001 spending some time in...
Hello,
I'm starting a new nRF51 project on mbed for a custom board. I wish to know what is the "cleanest" way to define pinout (what file to edit) ?
Thank you
I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
Hello, In the DevAcademy lessons I'm currently running blefund_less2_exer1 on the nRF52840 board. Successfully build and flashed firmware using Visual Studio Code enfironment...
Hello, I am trying to find out my nrf 52840 chip revision. I have tried using the NRF_FICR register but I couldn't find the revision there. I found that the variant is AAD0...
Hi
This is a project that reads sensor data and transmits it to the phone. Currently, the sensor data is read and transmitted to the app.
However, if there is 0x00 in...
anyone can tell what is the "Top right-hand side" sector?
Please see below screenshot.
Left hand side is what I dragged and dropped "merged.hex" from \asset_tracker_v2...
I am working on a module MS12SF1(nrf7002+nrf5340). I am using wifi,ble,sdcard,uart and https functionalities in my code. Currently my flash usage is 72.44%. I also want to...
Hello,
I have an aplication that connects to a LTE network and sends periodically a post request with some information to a http server. To get IP server address, I use...
Hi all,
I have an issue with putting my second boot slot on an external SPI flash. There are more people on the Q&A with issues in this realm, but none that I found were...
In our custom board, nrf5340-nrf7002 ,using external RTC ECS-RTC-SOP8-5101A RTC module, which is connected via the I2C bus.
We have configured the RTC's /INT pin (P1.01...
I am using a nrf52840 dongle. I have my own device which has BLE and I am connecting to an app in mobile phone our bluetooth. My goal is to check for the security level what...
Hi , on this code there are not any problems, ,it runs good. but the problem is current.it is 36uA. it is more than ecpectation. because in datasheet.
adxl362 current consumption...
nRF52833 Onboard jlink is broken what to do?
nRF52833 Onboard jlink is broken what to do?
Who can tell me how to make it work, and nRF52833 comes with Debug in and Debug...
Hello, I am using the peripheral_lbs example project and build it for nrf21540dk_nrf21540
I also added CONFIG_SERIAL=n, CONFIG_UART_CONSOLE=n for disabling uart.
But still...
Hi all
I currently have a project where i send and receive commands over UART to another chip. When i receive a message over UART, a callback is triggered and I continuously...
I am having difficulty getting the nrf_regulators_system_off function to work correctly on newer versions of the Connect SDK.
In earlier versions v1.3 and such, the call...
Hi, Wanted to report an issue with iOS BLE transfer speed being lower than expected on nRF5340 (nRF connect SDK) We tried to get the same throughput on BLE as nRF52840 and...
