Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi, team.
I am trying to find a way to write some persistent data in factory.
The data is a couple of certificates and should be written differently for each devices....
I am a beginner, and there is no problem with scanning and receiving data in RTT Viewer. I am currently stuck on how to use CDC ACM US. i have notice there are example on...
I am interfacing with a part that uses the same pin, P0.6, for two purposes:
1) The pin is used for UART communication. MCU RX input.
2) The pin is used as a GPIO. MCU...
Hi Everyone,
I have a custom board with a nRF9160. I have updated the firmware to 1.3.3. I am using SDK 1.9.1. I found that the board works well with the GNSS sample from...
Hi, I have an application where I need a latency below 100µs between transmission and reception over the air of a 32 bits payload.
We are currently evaluating the ESB protocol...
May I know if developing using the example of proprietary_rf that does not use BLE in SDK is also subject to a user fee? (If there is a usage fee, I would like to know the...
Hello,
I have an issue with BLE-Mesh, wherein If I provision a device and then flash the board with a new image (I do not erase and flash), the device name & provisioning...
Hi all,
we are using UART uart_rx_enable() to define a timeout of 500. Most of the time, event UART_RX_RDY is raised as it should be after a timeout. If, for example, we...
Hi!
Which is the right way to install nrfconnect SDK for VS Code for linux? Is it automatically or manually as described in the documentation?
Regards.
Hello all, I hope you are doing well.
I Have a project on NRF52840 in which I have multiple sensors connected to the NRF52 and the sensor data are storing in the SD card...
I have received a development kit from Farnell. It has version 3.0.0. When I connect an external target, I can't get a connection. It only recognises the onboard chip. An...
Hi there,
I would like to use SMP for DFU my Firmware and communicate with other SoC by one UART port. And then, in SMP protocol specification,I saw there is an ID (64)...
Hi,
I got a new nRF52DK, started working with it. After Blinky example, I tried UART example.
UART program is working fine. But Now i can't reprogram DK.
I tried to...
When I toggle pin 12, it toggles pin 11 as well. When I toggle pin 11, nothing happens. I also checked pins 13-18 to see if they were affected by both pin 11 & 12 and they...
Hello Everyone I am working on DFU over Mesh and followed this guide https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.meshsdk.v5.0.0%2Fmd_examples_dfu_README...
