Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Hi,
I am working NRF52840 Dongle board, I am using ble_app_uart program with some custom code, from that I am facing some problem while connecting the device in nrf connect...
Hey All,
I am using a non commercial license of SES (v6.30). Initially as PoC I built code with a TX/RX combination using the examples/peripheral/usbd_hid_generic/ for RX...
Hello Devzone,
I want to incorporate DFU in my project for the microcontrollers I am using. I have a nRF52840 which is my main controller and to it I have a nRF52832 connected...
SAADC feature request: RESULT.PTR auto increment Right now, continuous sampling works well for a high sampling rate (up to about 200ksps), keeping DMA etc active to cope with...
Hi,
Im using the nRF52840 DK and im trying to set the Service and characteristics with this tutorial : https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial...
I have one light sensor model publishing light lux level of the room to Group A . On other hand, have occupancy sensor publishing to the same group A .
and one light with...
Dear All, I am working on an application where I am connecting to the network, sending some data and then disconnect using CFUN=4, in order to achieve low power for my application...
Hey Nordic's technical team,
I'm trying to write and read via I2C to a component with two bytes registers. I tried the following method:
Then switched to this one: ...
Hello,
Using v1.9.1 nrfConnect and the Coordinator example on a nrf52840 -DK. From Nordic docs: I think I may be miss interpreting Zigbee Cluster spec... Below is example...
Good day
I have noticed that on my new DK boards if I touch VIO REF on P20 the PCB resets or stays in Reset if I keep touch the pin. My older boards never use to do that...
I want to set the GPIO of NRF52840 to the high resistance state. How do I set the GPIO of NRF52840 to the high resistance state, please help me,thanks!
Hi！
I'm working on direction finding using nrf connect sdk.
I have already make a tx (nrf52833) and a rx (nrf52833) and i succeed to receive the CTE and the IQ sampling...
I am working on adapting a project that compiles/flashes the code with a makefile that uses nrfjprog in a cmd line to program a blank nrf52480 with the softdevice and application...
Hi all
In nRF52840_PS Pin assignments sheet, some pins Recommended usage is " Standard drive, low frequency I/O only ", does that mean only low frequency (up to 10kHz...
