Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
i'm writing a code for mic without using i2s because that mic will generate digital pdm signal.
i saw there is no solid code for low level driver or hard coding
Hi I want to set up a simple uarte communication between a NRF52832 and a faulhaber mcdc 3002s motion controller using the libuarte. I have max3232 logic converter in between...
Hello,
while migrating our FruityMesh framework to SDK17 I went through all SDK and SoftDevice release notes and migration documents and saw the following:
Now, to...
Hi Nordic Team,
Few questions about Power supply supervisor block of nRF52810. My device's supply volage (VDD) is 2 volt. I have enabled POFCON and the handler is getting...
Hello. I am designing an application where the goal is to send a notification, sleep for 1 second, send another etc.
To do this I used the application designed in this guide...
Hello,
I'm working on KX132-1211 accelerometer with nRF52832 and am using I2C(TWI) protocol. For that I need to create driver files even I was contact with manufactural...
Hi,
I have a model_handler.c which builds fine, but the moment I change it to model_handler.cpp, I get build errors saying "duplicate descriptor is not allowed". I am struggling...
Hi, There is code for vendor model element creation in nCS provided Chat client sample, as in below:
This works fine in "model_handler.c",
But when I import the same...
nrfjprog checks the target for 0xFFFFFF before attempting to write.
It should be successful not only if attempt to write the same value as is already present but also
...
Hei, jeg evalurere et Reinsdyr projekt der 30 Reinsdyr skal løper inne i en binge, er det mulig å motta kun beacon fra BLE taggen i nRFAPP fra de 30, hva er max antall når...
Hi!
Using the nrf5340-DK, I am preparing a code to be used on a custom board, where the pinning configuration will be different from that of the development board. I have...
Hi
I am using the nrf Connect extension in Visual Studio Code on a Window 11 machine together with C:\Nrf_Connect_SDK v1.9.1
After having installed the nrf Connect extension...
Hi,
I am working with nRF52832_dvk board, i am testing the OTA example as per in this link. https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts...
Hello, I'm starting to design the pcb for the nrf52840. I looked but I saw that it is also possible to create it on two layers instead of four as the reference design teaches...
Hi,
I am trying to burst read FIFO of ADXL362 with zephyr adxl362 sample. 1 byte tx (read fifo command) and n byte rx ( reading the fifo data);
Zephyr is the last version...
