I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
I am using
MF V1.3
NCS V1.6.0
nRF9160Dk V0.15.0
Project: AGPS Sample
If i set the Interval in the gps_config structure to any number under 240 and run the sample...
Hi,
We are working on nrf52840 in that we have some doubt how to test the radio tx and rx in datasheet you have mentioned
Active mode Tx Current - 4.8mA and 0dbm ...
Upgraded from v16.0.0 to v17.1.0 and have a truncation issue. It only occurs after the first send. Reverted back to v16.0.0 and all ok.
No other code change other than the...
I've searched around, but i couldn't find anything about how to use DMA with SPI master on a nRF5340 (and zephyr doesn't support DMA on nRF5340 right?). Can someone point...
Hi,
I'm using ble_app_uart to test AT.
When I sending a buffer
reset_buff[10]="AT+RESET\r\n";
RTT log showing an error
<error> app: ERROR 4 [NRF_ERROR_NO_MEM] at...
Hi all,
I'm currently trying to interface an nRF52832 with an external Flash chip via SPI
I have tried with both NAND and NOR types, specifically the MT29F2G01 from Micron...
I am trying to develop CAN communication using nRF52 dev kit based on nRF52832 (PCA10040) and a MIKROE CAN SPI click 3.3V board . This board has an mcp2515 stand alone CAN...
Hello,
I had RTT configured as the logging backend and it was working fine. When I enabled the SHELL on RTT, the log output stopped. Maybe more specifically, printk() output...
Hello there,
I'm trying to downgrade nRF Programmer from v2.0.0 to v1.4.11 as it is not possible anymore to select a Segger debugger as target device in the newer version...
Im trying to make a simpel project reading the sensor BME280 over SPI. I can´t get any activity on the SPI pins when i check with my logic analyzer.
I´m using nrf9160-DK...
I've based my code upon the HIDS keyboard example and added code to support an attached polled sensor with I2C interface. The device will pair with the Android phone just...
Hello,
I'm writing an application that sends cycling power information via ANT+ and Bluetooth (S340, on a nRF82840). While the ANT+ is a pure cycling power service, the...
Hello,
I am using the Nordic SDK at v1.5.0, to create an application that runs on the Nordic nRF9160.
In the typical use case scenario, my application is mains powered...
Hello. 'm trying to DFU using serial bootloader with my custom board.
I've wired my custom board's nrf52833 pin with a USB2UART board.
nrf52833 RX Pin: P1.02 -- connected...
