Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Hi
I am using nrf Connect sdk 2.9.0 Visual Code IDE.I have added the following configuration in the prg.conf file:
But still I am not asble to receive more than 20 bytes...
Hi Support Team
We want to use the J-Link of nRF54L15DK to program customer's nRF54L15 board. We follow the guideline of below link to connect the Pins of P19 of nRF54L15DK...
Hi, we are using NPM1300 with a ICP401835TPRT renata battery. It has a 10k B=3380 NTC (part number NCP15XH103F03RC ). I'm getting a really high temperature reads and very...
Hi,
I am trying to optimize a time critical device for lowest possible latency data transmission over BLE on nRF5340 working as peripheral. Currently my algorithms are implemented...
I'm adding MCUboot to my application and we'll be using our own app to upload new firmware over BLE to the device over our custom comms protocol. I can use the DFU Target...
Working on a nrf5340 project, and running into limits of the size of the flash to store my application image along with mcuboot bootloader.
I had a mucboot setup that fitted...
I have a modified asset_tracker_v2 running with SDK 2.5.0. It is connecting to AWS and sending data perfectly. It has been running for several years without a problem. I am...
Hello,
I’m running the AWS IoT sample on nRF9160DK v1.1.3 using nrf-sdk and toolchain v2.9.0, modem v1.3.7.
Everything works fine when following the instructions with...
Hello community, I am currently looking for a solution outside the 2.4 GHz band and I came across NR+. Does it suit my needs for M2M (Machine to Machine) communication? If...
Dear Nordic experts,
My question is simple, how to get the 6 octets default MAC address by app SW in nRF52840. The question was already raised by someone some years ago...
I have an issue when trying to install nRF Connect SDK on my work computer. I have installed VScode, the toolchain and the nRF Connect extension. The next step would be to...
I have been trying without success to install either the v2.7.0 or v2.8.0 SDK onto my Windows 10 System. Every time/method I've used results in an error equivalent to
...
Hi,
SDK17, Softdevice S112, NRF52805 custom board.
I have baremetal bsp implemented but I am new to Softdevice and struggling a bit with an interface concept beween two...
Hi,
I'm working on an indoor positioning system using an nRF5340 and a CHW1010-ANT1 antenna array. I'm receiving IQ samples from BLE CTE packets and using them to calculate...
Hey,
I'm using the nRF5340 and want to run the PTS test with the following configuration: The CAP initiator establishes two audio streams within a single connection to the...
