I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
Hello everyone. I want to turn the LED on and off with the push button, if I want to hold it down after 3 seconds the LED will turn off, if it has been pressed for less than...
Hello
I am trying to port a custom project for nRF52840 from Keil to Segger Embedded Studio -uVision V5.33.0.0 -Armcc V5.06 update 7 (960) -SDK 15.2.0 -Device Familly...
SDK version: SDK17.0
We have low received radio message count with open USB CDC compared to when it is closed.
The low rx varies from 20% to 50%.
USB open = screen...
Hello!
what command should I send via BLE to disable the pressure, gas, and light/color intensity sensor?
In this documentation: nordicsemiconductor.github.io/.../firmware_architecture...
Hello
Assuming I set FDS_CRC_CHECK_ON_WRITE flag in sdk_config to 1, where do i get a notification that somthing went rong? I probably miss something but I need to clarify...
I'm using nRF52 DK BLE.
In the code, I used the following code to set the Tx Power = +4dBm.
On my HUAWEI Android phone, I use the nRF Connect app to see the RSSI. My...
To test the example, I downloaded the project through the following path.
https://github.com/NordicPlayground/nRF52-ADC-examples
I get an error like an image. What should...
Hi!
Hope you are doing well!
I am developing a BLE device and right now I want the device be able to auto reconnect to the phone.
e.g. The user leave home with...
Hello
SDK = ver 17
DK = nRF52
Using Peer manager for writing peer data in flash and FDS to store app settings in flash.
1. They both share the same spcase in flash...
Hi,
We are in the middle of product certification, right now with BT SIG testing. Unfortunately we got stuck right away since the test house cant configure the device...
NRF52832
SDK 17.0.2
SoftDevice 132
I am connecting with telnet to an exposed RTT port to see the logs. I adjusted sdk_config.h to use RTT instead of UART logging. The...
Question 1:
The nRF9160 datasheet V2.0 claims the sensitivity is: CATM=-108dBm (mid band); NBIOT=-114dBm (mid band).
However when the unit connects, we get a printout...
So in the MQTT example the following function is used to write the CA certificate to the modem so a TLS connection can be setup.
In our code/TLS setup we want to use Client...
