Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Hi，all:
There is a question when I run usb_msc example on nrf52840DK(sdk17.0.2)，I do as following steps,
Then,after I press button 1 for serial times,I found there are...
I want to get started with nRF52832 in Arduino. I have a Ebyte development board with E73 module containing the NRF chip.
The hardware is quite similar to Adafruit NRF52...
Hi,
Hope you are doing well!
I am trying to do Buttonless DFU on our own Android APP. I have finished programming on nrf end and succeed doing DFU on 'nrf connect...
Hello, I have done customized board using nRF52832 and when I try to flash code using nRF52 DK(Jtag) it is showing following error. could not fetch memory size of target devkit...
Hey all - I'm new and trying to connect Thingy91 to nRF Connect V3.6.1 for the first time. When I open the Programmer app I only see "No devices available" in the drop down...
Hi,
I'm trying to follow the NCS tutorial in: https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/getting-started/posts/nrf-connect-sdk-tutorial---part-1-ncs...
Hi,
we are developing a custom BLE communication. For this we are using:
- nRF5_SDK_17.0.2_d674dde - s332 - based on BLE NUS UART example
Everything works fine, until...
I'm trying to open a NCS project in SES but I'm getting error 1 from create_nordic_project.py. NCS 1.5.0 installed with toolchain manager on macOS 11.2.2
The error in SES...
Hi,
I am following a client case that they have issue on accessing SD card via SPI port.
I used the sample project fat_fs on nrf9160_pca10090 DK and used SPI_3 to access...
nRF9160 DK schematic sheet 2 missing pin names for WP and HOLD of nRF91_EXT_MEM in the On-board interface (far right page 2)
could someone post what nRF9160 pins are used...
Hi,
I have written one application with logging disabled to save power.
However, when I tried to debug the code with Ozone, during startup, it raises BusFault exception...
Hi,
I am currently working on generating a dfu over serial uart by testing with the ble_app_blinky example given in the SDK 15.2.0. Currently the ble_app_blinky hex file...
Hi ! Using nRF52840 whith SD140 as central and 6 link count I research :
changing the NRF_SDH_BLE_GAP_EVENT_LENGTH from 6 to 2 does not change "Window size" on CONNECT_REQ...
Hi,
I messed up my SES project and now the debugging session doesn´t start and the debugger does some weird stuff and doesn´t execute my application.
I also tested if...
Hi,
I am using the DFU example given in the SDK15.2.0 to try and update the application on my NRF52840. Currently, I have been able to update the application to run the...
