hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
We need to retrieve data from an FPGA to the nRF5340, process it with the network and Wi-Fi protocol stacks and then send the data to the nRF7002 for Wi-Fi transmission. We...
Hi!
Currently I have the following application requirements:
Use SPI peripheral to communication with FPGA device. ( NRF5340 [ SLAVE ] <---> FPGA [ MASTER ] )
The goal...
i'm trying to read voltage signals from a sensor using internal ADC.When the input is not connected,there will be noise. I use differential input pins like this:
NRF_DRV_SAADC_DEFAULT_CHANNEL_CONFIG_DIFFERENTIAL...
Hi,
i need to store few configuration bytes in non volatile memory. I found out there is settings module that can be enabled in Kconfig GUI (SETTINGS option).
My use is...
Hi,
I have successfully programmed the nRF5340 Audio DK as a gateway device using the Command Line Tools and by using the directives listed in the 'nRF5340 Audio' program...
I'm working on adapting ST's RFAL NFC library for ST25R3916B/X-NUCLEO-NFC08A1 on an nRF5340/DK in order to emulate an NFC tag, and have run into an inconsistency I'm hoping...
I have an application where I need to trigger time critical SPI reads of accelerometer data (sample rate is very crucial and data is fed into a FFT). In my current SDK based...
Hello!
I have added a UART and I2C to the Mesh Sensor Server example and on a custom NRF52840 board everything works fine.
Today I tried to add SPI without success.
...
1. Hi currently i am using nrf52840 sdk ver 17.1.0 s140 sd we have added UART in the secure bootloader/ Bootloader_ble_debug
2. we can able to send multiple bytes once ie...
I am trying to interface my PDM mic (ICS 41351) for a week now , and only got erros . Please direct me to a simple Project Code to use PDM mic with my nRF52840
Hello,
I am working on unidirectional voice broadcasting device where the maximum range is the priority. At this time I am developing on Audio DK boards.
I need some help...
Setup
nRF9160-DK
PCA10090 1.1.0 2022.4
Modem FW: mfw_nrf9160_1.3.3
Asset Tracker V2, I tried both the downloaded version from here: https://www.nordicsemi.com/Products...
I'm trying to send a parameter over BLE, but once i've stopped using the BLE stacked (and unininited softdevice) I can't seem to save the parameter recieved with pstorage...
Hello, I'm running the nRF5 SDK's ATT_MTU throughput example and I want to check that the data sent by the 'tester' (nRF52832 in my case) is effectively received by the 'responder...
I am trying to use mpu6050 with nrf52840, using bare metal programming. The program gets stuck at this loop -
while ( NRF_TWI0 -> EVENTS_TXDSENT == 0 ); what is the problem...