I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
I am running on a Windows 10 PC.
I've downloaded and installed all the tools for the nRF9160 DK using nRF Connect.
After installing the Segger Embedded Studio, I followed...
Parts of this discussion started on this thread: i-am-trying-to-do-dmx512-protocol
I am using SDK 15.2.0 on an nRF52810. My test board is based off of a Laird BL651 which...
I am trying to setup SEGGER Embedded Studio to program the nRF52840 dongle hardware. I followed the Getting Started Assistant program to set up the development software for...
The SDK version I am using is V15.0.0.
I use the function interface nrf_gzll_set_pa_lna_cfg 。 The following is my configuration information：
static nrf_gzll_pa_lna_cfg_t...
Hi dear community,
I am currently using nRF52 DK which has 52832 on it. I am using it for my bachelor thesis project and want to create simple sensor network. I am using...
Dear,
I am using nRF9160 DK,
firmware: secure_boot & AT_client
and Tale_SIM from Telia, I want to get the current GPS position by AT command?
Is it possible? Which...
Hi,
In a design which should be compatible with the NRF52832 we want to use the NRF52840. As the NRF52832 doesn't have USB, this would mean that the VBUS and data lines...
I am confused because i see documents referring to cmake/ninja and west. Recently it looks like people are suggesting to use west with master branches. Can someone definitively...
Hi all
nrf52840 Development board,sdk is nRF5_SDK_15.2.0_9412b96 ,PC is windows 10 .My testing master device is cell phone(Huawei HTC and so on,android system),and using...
Hi
nrF52840 SoftDevice S140 - What is the max ATT_MTU size supported? 244 bytes?
Is there any allowed number of packets per connection event that can be transferred on...
Hey, I just got this nrf52 board with pca10040 and tested few Nordic's examples, which worked just fine. I want to simply put some sine wave signal to one analog input and...
Hello all,
I'm working on a device using nRF52832, interfacing to another microcontroller. I was seeing higher than expected consumption, so started to reduce code to find...
Hi
I just downloaded the nRF connect v2.6.0 - Programmer, but i don't what i have to do to start writing the code.
I only get 2 ``Boxes``, and one of them is called File...
Hello,
I was wondering if there was a way to use the NRF SDK for Mesh DFU example without a serial port. Currently I have 2 Nordic Thingy52s with no serial ports so I cannot...
