SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
Hi,
I'm using the S132 v3 and wonder about the impact of DLE on scheduling.
In the chapter on Scheduling in the softdevive specification is writen that multiple peripherals...
I would like to setup the just released RasPI demo using the Nordic-Thingy52-Nodejs repo
I don't have a dongle, but 4 PDK 52840 boards and 2 Thingys.
Can I still use 1...
I found that blindly configuring all GPIO pins can stop the LFXO and RTC counter. I am reporting this as: something to be aware of, not obvious to everyone. Not a question...
I am testing the nRF52832 in Rigado BMD-301 module. I am able to get to ~40uA when advertising ,UART enabled but not used and all other peripherals disabled. But as soon as...
I connect to my BLE peripheral device using NRF connect app. While in connection, if I switch my phone's bluetooth off and turn it back again and then try to connect to my...
Hi!
I'm using the nrf52 on custom prototype boards and the official development boards. We are using the ADC to read analog values and encountered unexpected behavior related...
Starting notification and then writing 0x01 to the control point
does not cause the Buttonless DFU to enter boot mode. LED #1
remains on.
Run time trace show:
APP...
The Problem ist the continuous sending of Byte-Arrays with spi and fixed sample rate.
Strategie:
Send Array-List with XFER triggered by Timer (every 3ms) and auto increment...
Hello,
I bought Nrf 52832 breakout board .
Actually i want to measure the current consumption of chip as we want to use it.
While advertising 26 bytes it consume really...
I have questions about the HCI packet format
With the start packet, the Ack number in the header section = 000
What should it be filled in the data packet and...
I'm implementing an I2C communication and I need to set an interruption every time the sensor sets the interrupt pin to 0. I've been checking some other posts from devzone...
Hello,
I am currently trying to power profile all aspects of the nRF52840, which includes the CryptoCell 310. The instructions say "
Testing
Test the CryptoCell Example...
I tried to use Timer2 as counter with event and interrupt. event is working. interrupt not.
<pre><code>
timer_count_cfg.mode = NRF_TIMER_MODE_COUNTER;
err_code = nrf_drv_timer_init...
s132_nrf52_5.0.0-3.alpha_softdevice.hex (/attachment/26a9916e1af8c97bcba7185035bd7b31)Hi, I am starting to work on NFC and Bluetooth pairing for the nrf52 and i tried to compile...
