Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
Hi, After successful provisioning using "nRF Cloud Multi-service", I can view device on my nRF Cloud account. It shows successful MQTT and CoAP connections and GPS tracking...
My project uses ESB for communication. In our hardware design, nrf5340 + FEM is used. Nrf5340 uses two GPIO link FEM chips to switch between PA mode and LNA mode. May I ask...
Dear Nordic,
I am considering to make a board that includes an nRF5340 + display. I am looking at a display that supports QSPI and I was wondering if the nRF5340 QSPI can...
Hi,
I am learning nRF52840 development and making a sensor device.
The datasheet of the nRF52840 chip says:
Regulated supply for external components up to 25 mA
...
Hi,
I'm working on a project with the Nordic nRF9160 Development Kit and am trying to send Bluetooth beacon data from the nRF52840 chip to the nRF9160 chip using UART and...
Hello,
I try to enable the LE Data Packet Length Extension. According to the available documentation, it should be as simple, as adding `CONFIG_BT_USER_DATA_LEN_UPDATE=y...
When loading empty software (zephyr based) into the nRF9151, the nRF9151 uses roughly 4mA and when erasing the IC, it uses 5.8mA.
Does zephyr not include a power down mode...
Hello!
I am porting a nRF Connect v2.9.0 application from a nRF52 to the nRF54L15.
We are using PPI/EGU to get exact measurements for some BLE radio events for some optimizations...
Hi,
We are developing application software on the nrf9161dk that uses the little FS file system running on external FLASH. Most of the application development has been completed...
Hi
I want to use P0.18 gpio as output pin and not as reset for nordic.
I am using ncs v2.0.0.
I have added
CONFIG_GPIO_AS_PINRESET =n in prj.conf
and when i...
Hello,
I have a Nordic Thingy:91, and I need to perform continuous wave (CW) transmission tests in LTE. To achieve this, I plan to develop custom firmware that alternates...
Hello Everyone,
We are working on a new product using the nrf52840 and OpenThread.Our current product uses the Azure IoT Hub and we were wondering if we could use the library...
Hi,
I defined __STACK_SIZE as compile/build flag. It has no effect according to GCC output after building is done.
Chip is nRF52840.
I tried to set fixed stack size...
