I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
Hello,
I want to combine BLE, ANT+ and Apple Find My in one project.
I have permission to use ANT+ and Apple Find My.
I ran the two examples separately and they worked...
I have noticed that the RESETREAS register does not accumulate flags even though the documentation says it should. " Unless cleared, the RESETREAS register will be cumulative...
I have recently purchased a nrf7002 EK from element14.
I have connected it to nrf5340DK board and tried flashing the Wifi-shell sample application(with the help of video...
I’m not sure if I’m posting in the right forum, but since the EVK-ANNA-B402 uses the nRF52833, I thought this might be the place for questions related to it.
Steps followed...
I am using the cdc_acm example and have added a command to set and read tx power. I am trying to use the following commands for this.
BT_HCI_OP_VS_WRITE_TX_POWER_LEVEL...
Hi,
while using the SoftDevice with MPSL on NCS/Zephyr (nRF52840), there will be a HardFault triggered without using Monitor Mode when a breakpoint is hit.
I understand...
Hi Nordic,
I have installed nRF Connect for desktop for using with nRF5340 Board . After completing the installation I'm getting the following Error.
I have reinstalled...
Features
nRF52840
nRF52832
System current consumption DC/DC at 3 V
0.5μA at 3V System OFF mode,
no RAM retention
1.5μA System ON mode, no RAM retention...
Hi
I'm running the blinky sample (modified) on a custom board based on nrf9160. When compiling with SDK2.3 and toolchain 2.3 the current consumption is about 84uA (LED off...
Hi,
I use VS code (windows 10) to program nRF9160DK under modem mfw_nrf9160_1.3.6, application Asset Tracker V2, JITP certificate generated by nRF Cloud and good SIM card...
What is the power consumption to check battery level?
How quickly at boot time is an accurate battery state of charge available?
What is the RDSon in the path from VBUS...
Hi,
I need to read the registers of the KTD2026 IC as specified in the datasheet.
In short I have to send a read command with the device address (0x30), the address...
Hi, I'm working on a BLE peripheral project using nRF52840 with nRF5SDK version 17.0.2 and softdevice S140 version 7.2.0
We are considering to increase our full device name...
We are starting a new design that requires a LTE-M chip. Upon comparing features between nRF9160 and nRF9161, I see 2 differences
DECT NR+
3GPP Release 14
First...
Hi,
I am reading through different Nordic documentation. In some documentation, it shows a first stage B0 Nordic bootloader. This bootloader then can point to MCUboot...
