In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hello.
I am trying to write protect the Flash area using nrf52840's ACL peripheral. I tried to perform the same process on the main processing side by referring to nrf_bootloader_flash_protect...
Hi friend,
I use SDK16.0, and the version of softdevice is S140 V7.0.1. Can I advertise a special data? like 0x08,0xff,0xa6,0x02,0x33,0x09,0x55,0x00,0x0c. 0x08 is packet...
I am looking for to buy(I don´t have a 3D printer) a enclosure to protect my nRF52840-DK. It is not a good practice to handle because probably soon this practice will damage...
Hello, I just receive a nRF9161 Development kit and I'm completely new to both nRF9161 and Zephyr.
I want to start an evaluation project based on the nrf9161 lwm2m client...
Setup:
windows 11
VS studio code
Toolchain and SDK v2.6.1
hardware: nRF52840DK / PCA10056 (bought June 2024)
Using sdk/zigbee-Template as the base for the project...
Hi all,
I'm using an nRF5340 DK and I want to build a simple project that plays a sinewave to an i2s DAC (MAX 98357A, perfectly working on other development boards I have...
Hello,
I found that after bonding, I could still connect to another board that had burned the same code.
Here is all of my code related to pairing and bonding.
Central...
Hello,
I tried to find information about using the QSPI with external flash on nrf connect SDK.
My goal can be split into two parts:
1. Use QSPI with external flash...
Cant Flash Thingy52 on VS code after flashing once and also cant read sensor values of thingy on serial terminal. How can i flash on thingy52 smoothly like flashing other...
My programm uses both the non-secure world and the secure world, with the non-secure-world largely just calling functions inside a custom partition of TFM in the secure world...
Hi,
I'm working with a nRF54L15 within the nRF Connect SDK on Zephyr. I need an array which retains its content through soft resets, so in another RAM section than the...
Greetings,
One question on the nRF9161/51 capabilities: is the 3GPP Rel-14 LTE-M Cat-M1 larger UpLink transport block size (TBS) of 2984 bits supported (instead of 1000...
When debugging a connection using Wireshark and the BLE sniffer, one must select the device of interest from the device menu, or select "follow le address" in the key drop...
I'm checking the nrf_dm sample with NRF52840DK,nrf connect SDK.
Due to peer.c and dm.c create static thread,so I run debug and hope to get all thread and their priority...
Hi,
I am checking the i2c protocol with nRF Connect SDK and Zephyr through VSCode.
I created a very simple example where I push a button on the nRF52840 DK and I get the...
