Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hello:
I am Enrique Martinez. Currently I work with nRF52840 in nRFConnect SDK for VS Code. I have problems with documentation about Multi-Image builds ( https://developer...
Hello:
I am Enrique Martinez. Currently I work with nRF52840 in nRFConnect SDK for VS Code. I have problems with documentation about Multi-Image builds ( https://developer...
I am using the Direct Test Mode sample as a starting point (samples\bluetooth\direct_test_mode). I am using NRF Connect SDK Toolchain v2.5.0 and NRF Connect SDK v2.5.0. I...
As far as I know, ppk2 is an eye-catching and open source power evaluation tool. I got the source code of the power profiler from github, and obtained the hardware design...
Hello,
With the CMakeLists file, is it possible to make an error during compilation if the SDK version is not the correct one?
Example: I am developing an application...
I'm trying to modify this bit-banging ws2812 gpio Zephy driver to run on an nrf9160 board. The problem is I can't mange to get consistent pulse timing using assembly instructions...
Hello
I have a problem setting up communication between a nRF9161 and a nRF52840.
I have a custom board with a nRf9161 and a nRF52840. These two are connected with 5 lines...
Hello, I'm using the nrf5340 and nrf Connect SDK 2.6.1. Currently the MCUBoot is immutable and the cpuapp image is encrypted (it contains IP and secrets). The MCUBoot is kept...
Hello,
I 'm updating from Zephyr 3 .2.99 to Zephyr 3 . 4.99 .
I attempted to add a main() function to my application . (Heretofore I have not been using a main() function...
hello I am designing a custom PCB using an nRF5340 and i have one nRF5340 audio dk with me and both are configured as a gateway and headset . i am facing an issue in pairing...
To do this by reusing the sample of nRF5340 Audio I am thinking of using it by editing the overlay file.
nRF5340 Audio has A/D linked to P0.24, Use P0.24 separately from...
When I tried to use the sd_ble_gatts_value_get() function and found no error but no corresponding value returned, I was sure I had the right value in my feature because it...
Hi,
I try to create a one-button minimal "smart watch" based on a small nRF52840 module (register button press) and a second nRF52840 'central station' (receiving and converting...
hi there i hope you are doing fine and best of your health. actually i am developing the custom app to communicate with nrf 52840 soc device through bluetooth, which is working...
I am using PCA10056 3.0.2 dk for my application
when search for schematics of this version board I am getting 1.0.x https://docs.nordicsemi.com/bundle/ug_nrf52840_dk/page...
