In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
We use nRF9160 with our board (with Serial LTE Modem 1.9.1). Now we are at the production stage and we have more cases when we cannot get access to the mobile network. We...
I want to use nRF Connect for Desktop program 52840.It's very great except can't lock entire chip.
how can I lock entire chip by nrf connect like nrf studio?
I have built a system with 2 MCUs communicating through I2C. The NRF52 is I2C slave and the other MCU is master. I have implemented a command style interface which sends commands...
Hi
We have a strange problem with the Kconfig of the azure_iot:hzb sample project from the v.2.1.1 SDK:
We have configured f.e. the "Azure Iot Hub hostname" and the "Device...
Hello!
I have a custom board that I am trying to set up but I'm not entirely sure what to do.
In my board, I have an nRF5340 SoC, that has 2 interfaced with the external...
Hi Nordic team
I found a sample for ADC (saadc) on the nRF5340 at the end of this post . The answer is related to the nRF5340 PDK.
Is there a way to use this code on a...
Dear Team,
We would like to add nfc feature to our product. We are bit concerned about the nfc antenna size that comes with nrf52 dk.
What is the smallest antenna size...
Hi,
I am trying to install nRF Connect SDK using Toolchain Manager in nRF Connect for Desktop. I seem to consistently fail with this error for the latest version v2.1.1...
Greetings,
We are currently evaluating the nRF Connect SDK in comparison to the nRF5 SDK for our new product (BLE enabled & battery powered) for which low power consumption...
I'm having trouble activating a PDN on a running/connected device. Here's the code:
Seems like I'm missing something here. pdn_init does get called on system setup...
Hi,
Just wondered about the following ....
Strange parts of this code ... Or things I don't understand
After the first READ in Setup() it successfully reads the data...
I am trying to implement a simple uart echo test using nRF21540 DB board, but I always get NRFX_ERROR_FORBIDDEN when trying to transmit.
This is the initialization code...
I am using nRF5 SDK v16.0.0 on nRF52832. IDE is SES. I am also using FreeRTOS
What order should the following methods be called in? Does it matter when fds_app_init is called...
Hi Team,
I am using SEGGER 5.4 IDE and NRF52840DK controller.
I did not understand the difference between Terminal Emulator and Debug Terminal in Segger IDE.
I am not...
Hi,
I want to configure Timer1 (32 bit ) to run up to 1 sec and then reset. I want this to be done continuously with the help of Short but without using the event handler...
