I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
HI,
I start a scanning and print advertising report when address match on nrf5 SDK v16.0.0 with S140 on nrf52840. It goes well until I enable GNU extension in Keil. I don...
Hello. I have a project that needs an update.
The project was working before July 2022. However, now it doesn't work anymore (VsCode run/debug doesnt work) anymore. The...
Greetings,
during test of a device, we have tried uploading a shell sample in a nrf52840dk board. However for some reason this caused the board, or at least the installed...
Hi - I am using nRF5 SDK v17.1.0 and Segger Embedded Studio v6.34a. I am testing the ble_app_buttonless_dfu for pca10040_s132.
I am compiling ble_app_buttonless_dfu_pca10040_s132...
Dear Nordic Engineers
I would like to use the DFU trigger library to realize the NRF CONNECT for Desktop enter bootloader.
I found a demo in devzone: https://devzone...
Using a MAC running Monterey, VS code runs from command line on a terminal window from everywhere. When clicking on the "Open VS Code" button from the toolchain manager it...
For the nRF5xxxxx series, it looks like it has a differential ADC with 8 positive and 8 negative channels. It also looks like it has a scan mode where it will sequentially...
Hi,
I have a nrf9160DK and flashed it with Serial LTE Modem sample, however all the AT commands are just timing out.
Configuration is default and UART 0 is used.
...
Hi!
I want to connect my NRFL2401 to my computer using BLE (v4.0.0) in order to collect data from a sensor. However, the «Start Scan» button is not functional. When I click...
Hi!
I am trying to subscribe to nrf cloud with topic " prod/<TEAM_ID>/<DEVICE_ID>/jobs/rcv". After that I get Disconnect event in the MQTT handler.
Topic "prod/<TEAM_ID...
Hello Everyone,
I am using NRF52832 in my project and in my project I want to charge the device through USB C. So when we plug in USB C into the device, the NRF52832 should...
I followed the directions for pulling down the nRF Connect SDK v2.0.2 via Toolchain Manager v1.1.3 in nRF Connect for Desktop v3.11.1.
I am using Ubuntu 22.04.1 LTS 'Jammy...
Hi,
I am creating a central code from scratch, using zephyr version 2.0.1. I want to know the central code contain all the zephyr rtos property like thread in background...
Hi All,
I am trying to communicate with IC MAX17201 using I2C interface. I am able to detect the IC and communicate with it.
When I read 8bit registers from the IC I don...
Hello,
nRF5340, NCS2.0.2, vscode.
\v2.0.2\zephyr\samples\bluetooth\periodic_adv
when TX and RX work on PHY_1M, two side work well.
but when TX side set BT_LE_ADV_OPT_CODED...
