In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, I use nRF52840, with SDK 15.3.0
Using UART communication, stored data should be unsigned integer 16 bit.
And the data should be calculated to float data type.
...
Hello there. I am wondering if PWM peripheral in waveform is able to generate a following sequence:
The idea, as you may see, is to generate a sequence with the same Duty...
Hello!
We have hit a wall trying to add support for a particular BLE peripheral to one of our products (which is acting as a BLE central). We support other peripherals,...
Hi Nordic Team,
We have no problem with using ble_app_hids_keyboard app,
However, in some use cases, we would like the application to run as "Just Works" to access other...
Hello everyone,
I'm currently developing a custom firmware for the Nrf52840 usb dongle ( https://www.mouser.de/new/nordic-semiconductor/nordic-nrf52840-usb-dongle ). The...
After power-up and RESET by RESET pin, power consuption of nRF9160 is ~2uA.
After wakeup by WAKEUP pin and AT#XSLEEP=2 power consuption is ~23uA.
What causes increased...
My goal is to use the atmel winc1500 wifi module with the nrf5340. - NRF5340 - NCS V1.9.0/Windows 11 - Atmel winc 1500 I started from the http_client sample (ncs\v1.9.0\zephyr...
Hello, I have soldered up a 51822 and I am trying to connect it with an EmStat pico and get measurements. I am not sure how to program the chip and get it discoverable with...
Hi,
I am using the NRF52840DK and would like to configure the GPIOs to have levels of 1,8V by using zephyr 2.4 or zephyr 3.1. By default I am getting 3 V.
Can anybody...
Hi,
I need help to use FT2232H wit OpenOCD for flashing and showing debug messages from nRF52833 Dev Kit.
Background:
I need to distribute the debug environment to...
Hi there,
We are implementing the %CONEVAL AT cmd in our project and noted that the DL-Pathloss parameter, which is supposed to be the last parameter received, is not being...
I have 3 development kits, two of them work fine with the Audio demo application and one does not: the PLAY/PAUSE button isn't doing anything.
I've probed around the switch...
I'm following this guide to add On/Off switch to the template example.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.0.2/nrf/ug_zigbee_adding_clusters.html#add...
