Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
1) Our device uses NRF52832 to connect with Android 7 system，use wireshark to monitoring，find not hop，is OK？ and wireshark delta time is Connection Interval ?
2) nrf52832...
Hello,
I need to use Port 1 pin 8 as an interrupt pin:
This results in the error NRF_ERROR_INVALID_STATE, when nrf_drv_gpiote_in_init() is called. Everything works fine...
Hi,
I want to monitor the connection state of my device as I have observed situations in which the callback functions defined with bt_conn_cb_register is not fired, causing...
Hi
I have build a sample project nRF5430_audio for nRF5340 Auido DK(two DK, one for gateway, one for headset), following the guide: nRF5340 Audio — nRF Connect SDK 2.0.99...
Hi,
I´m working on a project to send measurement data over ble and receive it. This worked for me, but I want to send the message in my own struct.
What I found in the...
I am trying to use blesniffer on wireshark. I have 2 nRF52840 dongles.
I have successfully captured traces using the 802.15.4 firmware on Wireshark with the dongle appearing...
Hello, I want to know if a typical 50ma Maximum DC-DC converter ic is up to the job of powering up the nrf52840 device working under the heaviest load?
I can't seem to...
Hi Devzone
currently i am doing some test on example central_and_peripheral_hr.
in the orignal example central_and_peripheral_hr is using the BT_SCAN_TYPE_SCAN_PASSIVE...
Hi,
I have a simple question: how to get the link key of nrf5340 audio dk when streaming as gate and handset; we want to catch the airtrace.
BR
Zhongsan
Hello,
I used the NRF52810 controller for BLE application. I have a code in which BLE advertising packet length is 32 byte i have to reduce it to 23 bytes
Following is...
I am a user developing using nrf52832. I have a question about TX POWER. TX POWER can be set to -40, -20, -16, -12, -8, -4, 0, 3, 4 by using sd_ble_gap_tx_power_set(). I tried...
Hi All,
I am using nRF52805 in my application development(), everything working fine and power management is initialized using "power_management_init();" function. But i...
Hi,
My product uses two sensors, and S113 on nrf52833
I need to communicate and compute data before to update my ble caracteristic.
Sensor 1 takes 45ms to do this tasks...
Hello,
I am currently in the process of integrating the hx711 library written by one of your developers in order to sample weight data from a load cell and send it to a...
Hi, I am new to HTTP, and are trying to make a simple http post (not https) code for thingy91 over LTE. I have a http server that require some headers in the request. I have...
