I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hi Team
im trying to change device name during running time..
i can able to change the device name working fine for connectable mode...but if i go for running time non...
the power consumption is about 6.12mW in BT connected, and consumption is about 7.75mW in advertising mode.
is it normal or has possibility to reduce it to extend the battery...
Hi, you must be sick of me!
Now that (somehow) I've got the BLE Secure DFU Bootloader to work on my nRF52840 DK board. I'd now like to load it on a nRF52840 dongle pca10059...
Hello !!
I am using ble_app_becon example code to send some data with device name. On central I'm scanning and searching with device name to identify at central side and...
Heija Guys,
I have a question regarding the usage of the Zephyr BLE and the PWM. I would like to use the Zephyr BLE Stack and the PWM Driver together. The Problem now is...
Hi,
i am working on dfu with NRF52DK. I am facing a problem with compiling a example dfu code "pca10040_s132_ble_debug" .
error message is "cannot find ../../../../.....
Hi,
We bought 2 pcs of nRF52840 Dongles and want to use them to test if a nearby BT device has the correct MAC address.
I've programmed them with "sniffer_nrf52840dongle_nrf52840_7cc811f...
Hello,
I'm using the "usbd ble uart " with twi scanner example to send a sensor value through an arduino 33 ble sense using nrf52832 and it works very well . but when...
Hi,
I'm using the light switch example in the nRF5 SDK as base for Ble-Mesh. I'm using a nrf mesh app for provisioning. I have both client and server model in my application...
When building a project that works with the SDK 1.5.0, I get the following...
r@mint:~/ncs.1.6.0-rc2/nrf/nordic_assist/nordic$ west build -b nrf9160dk_nrf9160ns
[0/12...
I am working on a custom board for the nRF9160 and currently have a DK and a thingy.
I need to make a serial interface available on the DK, thingy and a custom board I...
I want send data from Mobile over established BLE Mesh Network (through Proxy node to all nodes in the network) and also get data from BLE Mesh Network.
Data is customised...
I have not set nrf5340 i2c2,uart2 to work .
,in prj.conf ,add below configure:
CONFIG_SPI=y CONFIG_NRFX_SPIM2=y
in prj.overlay ,add below configure:
&spi2 { status...
I am working through the Getting Started documentation for the nRF Connect SDK 1.5.1 on a Windows 10 machine running SEGGER Embedded Studio Nordic Edition Windows x64, Release...
