Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
There is a demo zephyr/samples/subsys/fa/fat_fs. This purports to mount an SD card. Is this for the unpopulated SD socket on the nRF9160 board? The ticket https://devzone...
Hello Team,
First of all thanks a lot.
I learned so many things from your Nordic devzone:)
My problem: I have uploaded the blinky code using pca10040_s132_ble [ secure_bootloader...
Hi a bit a noobie here, but I can't connect to my nRF52840 on my custom board that I made. I have tried both an ST-link V2 with openocd, flashing it into a black magic probe...
This board is no longer recognized by SES to program code.
9:09:21.82 d:\> nrfjprog --recover ERROR: JLinkARM DLL reported an error. Try again. If error condition ERROR...
Hello, all.
I would like to connect one board that transmits data using the ble_nus , such as in the ble_app_uart example, to another that receives the data and sends...
I have been using nrf52833 Devkit with softdevice nRF5_SDK_17.0.2_d674dde have nrfconnect v3.6.1 when i merge hex file of softdevice 140 + ble_app_template then the following...
Greetings,
I've seen multiple references on how to change to the 2Mbps PHY after a connection is made, and I have that working.
Now, I'm trying to advertise at 2Mbps and...
Hi support team,
I am a beginner with Nordic nrf5 sdk for mesh. I begin with the sample light_switch. Currently I want to toggle the status (on/off) of the unprovisioned...
Hi
We need clarification about Nordic Advertiser Extensions (Instaburst) .
1. The document ( Nordic Advertiser Extensions (Instaburst) ) says that the maximum theoretical...
Sir,
How are you ?
I developted an BLE application (Segger Nordic SDK) to a chinese module and worked very very nice! I installed in 40 modules. All working
No i ordered...
Hi there,
I've just installed the "thingy91_at_client_2021-03-04_8e8c6089.hex" AT command client app on my Thingy:91 and I've connected to it via the nRF Connect LTE Link...
Is nRF5340 RF port S-parameter available?
I am looking for the S-parameter of the RF port so I can figure out the best matching circuit for my layout. The only S-parameter...
Hi ,
I want to build .. \mesh\bootloader, I know must use CMAKE, but I do not know how to use CMAKE?
Could you tell me or show me the step,please?
Thanks!
Looking for the nRF 9160 SMS sample mentioned in Getting Started. I can not find it in the folder mentioned.
This sample can be found under samples/nrf9160/sms in the nRF...
Hi,
I am using nRF52840 on my custom board and Mesh SDK 5.0.0. I am testing the Mesh Light Switch example on my custom boards(one for client and two for server)with battery...
