Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Would like to capture the HCI flow through rpmsg (Rx and TX) using the btmon tool between application and network core. could not successfully do it.
Procedure:
1. Build...
As mentioned in the DK board User guide nRF52840_DK board is preprogrammed, so, till now we didn't flash the DK board.
I tested the nRF52840_DK board using J2 USB connector...
Hello, with the new version of the nrf5340 version D in the NET CPU RTC0 stops to work and the RTC0 IRQ is not called
now for example the counter is stopped at 87 and the...
Hi,
My problem is that I can't sniff any advertising packet using Wireshark.
I have well followed the detailed procedure https://infocenter.nordicsemi.com/index.jsp...
BLE app uart code write to the BMD 350 device. BLE is disconnected.
If any reasons?
How to configure the TX and RX pins ? when i change the pins, fatal error will come...
Is clearing the NRF_UART_EVENT_RXDRDY really sufficient before exiting the IRQ handler? Since Cortex M4 is used, there's no need to clear the pending register (to avoid the...
Hi, Could you pls check, is it ok if these logs happened?
No firmware defined for selected device Please make sure the device has been programmed with a supported firmware...
Hello
I would like to modify the example "ble_thread_dyn_mtd_coap_cli_nfc" to use Just Works pairing instead of OOB with NFC.
To do this, I modified this in sdk_config...
Hi,
I worked few years ago on a project with the configuration below :
nRF Mesh SDK V1.0.1
nRF52832
I used the light switch example where the client and the provisioner...
Hi, I have built a project upon the aws_iot-example. There are three shadow-topics that the device may publish to (/update, /get and /delete). To me it seems there is no possibility...
So I'm trying to get to grips with the ble_app_blinky example from nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_blinky
To start with I grabbed the hex file ble_app_blinky_pca10059_s140...
Hi, 1. In ncs v1.5.0 nRF5340 I need to drive a spi peripheral w25q128 2. How do I generate this file?
3. Where can I find the syntax rules that generated this file? 4. Can...
Would like to capture the HCI flow through rpmsg (Rx and TX) using the btmon tool between application and network core. could not successfully do it.
Procedure:
1. Build...
Hi,
I have a custom board with nrf52840 with UARTE1 instance enabled for RS485 communication.
I have 2 boards on the same configuration and trying to send data to each...
