Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
we have deploy the serialization libraries in our host to communicate with nrf52840, but it seems the serialization libraries don't handle pairing/bonding event, so we can...
So I am doing a number of crypto operations. One of which for example is an ECDSA signing operation. I do that through mbedtls_ecdsa_write_signature which is using the CC310...
Hello,
We're currently evaluating the feasibility for leveraging our existing NRF51840 as host/system processor that runs all of our application code and runs the BLE...
Hi,
I am having some trouble. For a project, I need GPS, 9 axis IMU (accelerometer, gyroscope, and magnetometer), a microphone, and LTE connectivity in a small form factor...
Hi Team,
I am using nRF Connect SDK v1.3.0 tag for nRF52840 DK.
I am trying to integrate BLE HCI UART project files into Zigbee light switch project.
I have attached...
SDK : nRF5_SDK_for_Thread_and_Zigbee_v4.1.0
Hardware : 2x nRF52840 (PCA10059) + 1x generic overflow sensor.
This is an attempt to gather complete information regarding...
Hi,
I am using nRF52832 along with Softdevice 6.0.0, SDK 15.0.0, Chip Revision 2 (QFAA-EX0).
I am using nRF52832 as central device.
I see from sniffer that LL_VERSION_IND...
I have Power profiler kit 1 which was working fine. I have updated my nrfconnect app and since then on my power profiler kit, I am unable to perform battery power profiling...
Hi
I am trying to build the BLE Secure DFU Bootloader example using SDK 17.02 and the PCA10040 Dev board. Following various threads in the forum, I have been successful...
Hello, I'm trying to merge NFC writeable example " writable_ndef_msg " with BLE Beacon " ble_app_beacon ". My aim is to start BLE Beacon after the scanning of NFC. I have...
Hi, I've a timer configured by gpiote to capture with a second 'overflow' capture should the signal stop. I'm not using an interrupt instead the CC[0] value is being used...
I have seen the same issue reported.
nRF52840 DK does not appear as a removable drive named "JLINK"
Done the following.
1- My laptop has only one USB port. So I have...
Hi there, I'm controlling the nrf9160 with a esp32 and I'm wondering if you have an recommended libraries for forming AT commands and parsing the return messages?
I'm running through the nrf9160 dk startup guide and I've updated the application and modem firmware. However, it does not look like the application is accepting AT commands...
