Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Hi,
Just a general question, is there a way to find out the exact size of the advertising packet? I'm using nRF52832 to connect to a smart phone. I was curious if there...
Hello, I try to read from IM69D130 (as microphone) by nRF52832 (SDK 16) , And I work with PDM driver of nRF52. It seems it cannot read the data correctly. Here is my function...
Hi! Reading the documentation on NRF_PWR_MGMT_CONFIG_DEBUG_PIN_ENABLED, I'm left with a few questions.
1. Will this pin be set in all system sleep states? i.e System on...
Hello Everyone.
I'm getting falls values on the power profiler, I just connected a 1K resistor across the External DUT and the voltage is 3.6V so expected values should...
Hello Everyone,
I have done I2C communication with Grid Eye sensor (AMG 8832) using twi_master_with_twis_slave (nRF5_SDK_12.3.0_d7731ad) example program. Now i want to transmit...
When I tried to set up my J-Link Flash connection it gave me the message "Unexpected core ID.
First Dev Board R0.5 was normal. and marking of nRF52840 chip was QIAAD0 ,...
Hi,
On nRF52840, we are able to engage APPROTECT by setting NRF_UICR-> APPROTECT to 0. However, writing 0xFF to NRF_UICR-> APPROTECT does not seem to disengage APPROTECT...
If you call nrf_serial_write() once to transmit some data, and before the data from this first call is transmitted, you call nrf_serial_write() again, will the NRF_SERIAL_EVENT_TX_DONE...
Hi Team
I would like to know are there any pic libraries for nrf24l01?
Need to send and receive data from PIC16F1526 to an other PIC MUC via nrf24l01 transceivers.
...
Hi,
My task is to work on NFC , I know the basic working principle of NFC . Here I have seen the nfc uart example .
I would like to transmit the device name, mac address...
Need advice on choice of advertisement flags.
Beacon advertises alert and non alert beacons: On the alert beacons the central is required to connect and respond to the beaconing...
I have looked at and used the following references:
https://devzone.nordicsemi.com/f/nordic-q-a/47484/ble_gap_evt_scan_req_report-not-working
https://devzone.nordicsemi...
