Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
Hi all:
I am use ble_app_blinky demo sdk 16.0.0 I want to put system on idle mode,but there need to call two times sd_app_env_wait() so it can in system on idle mode.
...
Hey,
I am a new to BLE devices. I am using BL651 Laird Connectivity's 453-00005 module
and using standalone JLink OB ARM debugger to connect.
When I try to connect my...
Hi,
I want to get running the sample "lwm2m_client" on the board nRF9160DK (PCA10090).
Modem FW Version: 1.2.0.
I build the sample with Segger Embedded Studio v4.52...
Hello,
When I try to run a project containing a .cpp file, I get the following console output:
I am compiling the openthread client example with a slight modification...
Hello, I am trying to change the instance on the spi in the spi example, but unfortunately it is throwing me an error - implicit declaration of function 'NRF_DRV_SPI_INSTANCE_...
Hello,
I am using nRF52840 S140 v7.0.1. I have a query on Tx power settings.
1) In below snapshot under features, its mentioned as “4 dB steps”. So whether can I write...
Hello,
I previously used the latest SDK v17.0 on my nRF52832 PCA10040 board DK.
I ran the ble_app_uart example in order to understand how the Nordic UART Service works...
Hi all
I am doing a small personal project. I have 2 DK's :
nrf51 DK: pca10028
nrf52 DK: pca10040
Up until recently things worked fine, but suddenly i ran into a...
1. At present, using the Programmer burnmodem firmware in tool nRF Connect mfw_nrf9160_1.2.0.zip step is cumbersome.
2. Is there a simpler command line tool that can burn...
We have v0.8.2 of the nRF9160DK which has GPS antenna issues. We are looking to get the latest available version of the DK from Mouser/DigiKey. Is there any way to ensure...
Hi,
I want to use SPI to receive data from an ESP32 microcontroller to the nRF52840 development kit. Where can I find information/example regarding the same (I'm using nRF_SDK_17...
Hi
we have a custom board with nrf52810 chip, 32M crystal on it and using the zephyr version 1.14.1 as the firmware base.
Using zephyr samples/bluetooth/hci_uart
Custom...
