Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello everyone, I'm learning about MCUboot. Currently I have tried searching for information online but still don't have an overview. So I hope everyone shares their experiences...
I built blinky which just blinks a light, pretty simple :). Then I found Anroid nRF blinky in your git hub repo, that's a git hub project that remotely blinks a light. But...
In which subsequent process is the random_static_addr_cfg function reflected? Does the ID change with each build? If the ID changes, will it affect Bluetooth connections?
Due to project requirements, I have made significant modifications to MCUBOOT, but currently all projects use the same MCUBOOT file. Is it possible to have MCUBOOT configure...
I'm going to build an project with 2 AS5600 sensors, and also using I2C mux(TCA9548A) to communicate with 2 sensors.
I have some problem with devicetree. There are two errors...
Hi!
I used SDK15 (may be 15.3) with s132_nrf52_6.0.0_softdevice
I used nRF52832 in two modes in one time.
When I stay in connect with my peripherial to a central device...
Hello,
I have a custom board with a nRF5340 on it. The firmware gets built with MCUBoot in serial recovery mode to update the application core. The serial recovery mode...
Hello. I'm using serial lte modem as mqtt client.
After a while I receive fault. Adding logs:
#XMQTTEVT: 9,0 ESP:LTE: PINGRESP packet #XMQTTEVT: 9,0 PINGRESP packet CR...
Hi, I read somewhere that the LOG module works differently from printk() and uses a separate thread or so. But I couldn't find any information which priority this thread uses...
Hi there,
I am currently having issues flashing an nrf52840 DK on windows 11 using either west for a Zephyr project or nrfjprog. I have successfully done this on a work...
Hello,
I am designing a custom PCB using an nRF5340 and am unsure what my options are for how to program it.
I've seen a number of forum posts saying that you can program...
I've been working for a year now programming nRF5340 DKs using nrfjprog and I still can't seem to figure out what is the right way to program them. It is also very random...
Hi, I am working on the nRF5340, We will be using the nRF5340 for the device that we are designing.
How to do the very first production DFU/First firmware upload,.
I...
I have a device nRF5340 with multiple advertisers who have different services.
I differentiated the address with bt_id_create(), but I would also like to differentiate the...
