Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
I am using nrf52840, NCS v2.1.2.
I add MCUboot in my project, but got ‘Failed reading sectors; BOOT_MAX_IMG_SECTORS=256 - too small?’.
I add some log in MCUboot...
Hi,
I have been using the nRF5 SDK for years and the reason why I chose Nordic was for the low power consumption. Then when I was designing a new product using the nRF52840...
Board: nRF5340dk
SDK version: v2.1.0
My goal is to transmit 240 bytes of data every 5 ms using GATT notifications and 1 Mb PHY.
In the attached sample, I have my dev...
I added two extra buttons to ble_app_blinky (SDK 17.1.0) - port 1.10 and 0.31 I am running the code on an nRF52840 Dongle. The additional buttons are configured exactly like...
Hi,
I am using the sensor server example available in nrf5 sdk for mesh to build my own application on top of it. And the SOC we are using is nRF52832. I am trying to erase...
I see in the nrfx_uarte.c file the statement NRFX_LOG_INFO("Transfer about to send : %d bytes", length);
How can I set the logging for this file on?
#define NRFX_LOG_MODULE...
Hi,
My apologies if this is the wrong place for this.
I've been using the Power Profiler with the PPK2 and I'm very happy with the product, just have a couple small suggestions...
Hi there! I am facing " <err> download_client: Unexpected HTTP response: 400 bad request" error whenever I am trying to download full modem update from AWS S3 bucket. My environment...
Hi,
I attend the introduction course for the nRF's, and I am at Lession 3. The task is to print 'Hello World' to the device, using Serial Port and COMx. I have made the...
Hello,
As per the requirement of my project I need to add a header file into one of the thingy:53 sample.
Can you please guide how can I add a new header file into it...
Hi ,
I am working on thingy53 and using ncs 1.9.1 I need to enable the BMI270 sensor and need the acceleration and gyroscope data from it. So for that, I primary using the...
Hello,
I am using the provisioner example to provision and configure all my sensor nodes in my project. My use case consists of around 60 sensor nodes. While provisioning...
Hi,
I moved my code on a second windows pc, checkout the code from git,download the same nordic sdk and softdevice version, same SES version but running on my board, the...
Devices: nrf52840 peripheral to nrf52833 central
background: We switched the mode from BLE_GAP_PHY_1MBPS, to BLE_GAP_PHY_CODED. The content of the advertisement data was...
