Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi Sir,
We are a third party programmer manufacturer.
We are currently developing the nRF5340 programming software.
Encountered the following problems, please help to...
i2c_recover_bus is used to re-sync slave devices on the i2c bus when they may be out of sync due to a reboot or other event.
i2c_recover_bus is currently not causing the...
Hi,
I'm mid-way through designing a custom board using the nRF52840. As I am space and height constrained I need to use the Tag Connect style connector used on the nRF52840...
We want to be able to manually send Friendship requests from LPN or to change request interval runtime.
It was possible to send requests manually using nRF5 Mesh SDK, however...
Hi guys;
I try to read and write the data without connecting nRF52832 .is there possible to do? Then is it correct or not? if it's wrong means give me the possible solutions...
I have a DK board with nRF52832 that I've been using several months with no problems.
Today I wanted to try an experiment and did some modifications to the startup ASM...
Hi,
Our setup is a new design with SDK 17.1.0 and it is expected to support DFU over BLE. We are using the nRF52832 SoC.
I am trying to understand the role that is being...
Hi,
We are having an issue modifying the blinky_pwm example for our needs. We have made a devicetree overlay file setting the pwms of &pwm_led0 to 28 and pwm0's ch0-pin...
I would like to use nrfjprog to erase nRF52832 device. But it failed with "An unknown error". The nRF52832 device connect to laptop through J-Link USB interface.
D:\Nordic...
Agenda : Use crypto features like AES-CBC, AES-CCM, RSA, ECC, etc. in secure environment (i.e. trustzone with SPM). Also, to use HUK, KMU for secure key generation and storage...
Hi All, I am migrating some applications (each with multiple custom board) from nCS1.5.1 + nCS1.9.1 to nCS2.0.0 I also noticed that in nCS2.0.0 the build output folder is...
Hi,
Depending on how the nRF5 SDK is configured, the BLE address may change once in the bootloader (it's incremented). This happens in the gap_address_change() function...
Hi Everyone,
I am trying to do OTA on NRF52833. In my previous project I was able to do OTA on NRF52840. The memory requirements for the project were as follows:-
Memory...
Hi, I'm trying to configure my VScode project for the nrf5340dk using the nrfconnect sdk to be more version control friendly and require less interactions to set it up. I...
hi..... everyone
I want to send the data from one node to particular node and that same data should want to print in termite using uart . so i checked the ble_uart coexist...
