Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
On a MCU PCA10040 v2.0.0, I ran the command:
.\nrfjprog.exe -f NRF52 --program .\final_image.hex --verify --reset
Which subsequently caused the board to go into a reset...
I have a Thread bench-top environment set up that includes
One nrf5340dk flashed with the openthread coap_server firmware build and flashed on 1.8 via Visual Code
Two...
Hi
If a bug stop the application to feed the wdt,Is there any way to store 8bytes application data to flash before reset which occurred by wdt?
I find that there is only...
Hi,
I'm having some difficulties understanding how to manage commands in endpoint-specific callbacks. For example, when receiving a "ZB_ZCL_CMD_CONFIG_REPORT" I'm able to...
Hello,
I have a peripheral (nRF51822, S130, using the peer manager) that should be paired/bonded with one or many centrals. I have followed the example ble_app_bms from...
Hi everyone,
I implement nrf5_SDK_17.0.2 ble_app_uart example and I use an android app like nRF_Connect to receive the uart data on my cell phone.
The problem is that...
Hello,
I am having an issue with the nrf_libuarte_async librairie.
I am sending data via nrf_libuarte_async_tx and receiving the data properly via the IRQ handler...
Hello all, I am currently trying to get the nrf sniffer into the hardware of my nRF52840 DK board. Unfortunately when I call the programmer via the nRF Connect Desktop APP...
Hi, I am working on ble_app_uart_pca10056_s140 and after 3 minutes and I am getting the following error.
When I change APP_ADV_DURATION to 0 also get the following error...
Hi,
We have a product based on nrf52840 which is already in production for several years. It was built over SoftDevice132 and SDK 12.3.
The project has 2 components: ...
SD140
nrf52833, custom application based BLE Central Uart Project.
We would like to try the UART DMA functions available in Soft DEvice, s140_nrf52_7.2.0.
I have not...
I am trying to get I2S communication up and running but am unable to produce a signal on my SDOUT pin. MCLK, LRCLK and SCLK work as intended but trying to send any data does...
Hi! I've recently received my Thingy:91 and wanted to get it up and running. I followed your video ( https://www.youtube.com/watch?v=xQ7hDzRULJQ ), although did not see the...
Hi,
I am testing direct advertising with two nRF52-DK. One performs a direct advertising and the other scans for the directed adverts. Unfortunately, the scanning device...
The NRF52840 specifies a 20%, 10uH inductor for the integrated DCDC convertor. Why is the inductor value so large? This switcher runs at 8MHz, which usually means something...
