I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
I'm adding DFU over Bluetooth support to an existing application based on nRF Connect v2.3.0 following these instructions . What the instructions lack (and possibly is a given...
As the title suggests, I am trying to run the peripheral LBS example on my custom PCB to test BLE before continuing with my application. I'm using NCS V2.9.0. I have created...
In some other tickets it's said, that using the nRF7002 for IP traffic doesn't work, because that requires too many resources on the nRF9151.
Does this apply for a "UDP...
Hi,
Where are the peripherals required for the Zigbee stack documented? I have searched, but only broken links have been returned by Google. I'm using Connect SDK v2.9
Hello. I want to change the board configuration in nrf7002. "In the nrf7002dk_nrf5340_cpuapp.dts file &spi4 { status = "disabled"; }; An error occurs when spi4 is disabled...
Hello everyone,
My project consists on using the nPM1300 with ESP32-S3 on a custom board. I2C connection is pretty much validated, since I have already configured some...
I have an app where I'm using the AP and STA mode of the 7002. I'm running on a nrf5340.
*** Booting nRF Connect SDK v3.5.99-ncs1-1-1-g6dc48c918694 *** [00:00:12.620,269...
Hello,
I am new to Zephyr and I am trying to figure out the best way to set up a new project for a nRF91 modem. Ideally, the project should allow patching of the nRF Connect...
Dear All,
I am working on a project using the nRF52810 with the secure bootloader configuration from the Nordic SDK 17.0.2 . Specifically, we are using the example:
....
I've setup my development environment using the 'application' structure. https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/develop/application/index.html#zephyr_workspace_application...
With the nRF52840 we used RSSISTART to start the sampling of the RSSI and got a RSSIEND event when we could read the RSSISAMPLE register.
The radio on the nRF54L doesn't...
Hello,
I am working with the Multi-Service sample on the 9161dk and also a custom 9151 board.
The multi-service sample compiled option works great but the samples, when...
Greetings.
Background:
We have a custom device, that uses the nRF9160 as a Modem, with Modem OS 1.3.4 and a sightly modified "Serial LTE Modem" FW. One of our Devices...
I'm trying to send simple packets using the radio peripheral.
In my test scenario I have the following conditions:
The HFXO is started and is running the whole time...
hi
the lengths of the this track is important?
if i decrease this length, how i can set antenna parameters?
another question: what is the R1 =0 ohm resistor and N...
