Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
We integrated latest released version of "pc-ble-driver.py" & "nrfutil" in our custom linux os running on ARM 32bit based custom board (B1).
pc_ble_driver_py :...
Hello Nordic,
We have an NRF52840 with SDK 16.0.0 as central in our project and multiple peripherals (which are IOS or Android phones) are supposed to connect to it.
In...
Hi,
I have a custom board using nrf 52832. I am using SDK 15.2.0 and softdevice s132 v6.1.0.
I have referred following link
https://devzone.nordicsemi.com/f/nordic-q...
I have a Nordic thingy 91 connected to nRF Cloud, and I see a message "Upgrade your firmware to view Network, Sim, Device, and Service Information" I have tried to update...
The nRF9160 is connected to the nRF52840 by MCU_IF0 ~7(GPIOs) in the Nordic Thingy:91. and I know to uses UART communication between the nRF52840 and the nRF9160. Can I know...
Hi
a way to reset nRF9160 is by pulling low the nRESET pin https://infocenter.nordicsemi.com/topic/ps_nrf9160/pmureset.html?cp=2_0_0_4_0_4_1#pin_reset
During the entire...
Hello!
I would like to try the following using my nRF52840 board: press a button on the board and then receive a notification on the phone. And the other way round , press...
I am trying to update the DUT(Device Under Test) via nrf52840 Dongle with PC(ubuntu16.04/windows10) by the command as below:
nrfutil dfu ble -ic NRF52 -pkg OTA_DFU.zip ...
Hi,
This is actually a followup ticket based on this: https://devzone.nordicsemi.com/f/nordic-q-a/56228/fota-dfu-over-internet .
Now the situation is a bit more concrete...
Dear all：
I want to control my central( 52840 ) device to connect with peripheral(52810) within a range （45-60m），i change the tx power，but it set -4dbm，the distance is just...
Hi, I'm developing new project, and during test I see that, if you quicly connect/disconnect/connect.... and so on, the app seems locked... Tu exclude my HW-FW, I tried same...
Hi,
How to auto-connect with my BLE peripheral without an external application?
Here, the Android mobile acts as a central, and the nordic chip act as a peripheral.
...
SDK15.0.0/SEGGER/Windows
Hi, I ran this example: https://github.com/NordicPlayground/nRF52-ble-long-range-demo .
Note: Added NRF_LOG_INFO("%s", p_adv_report->data.p_data...
Hi, I have a problem with DFU upgrade over BLE on nRF52840dk. For some reason,the upload speed is quite slow ~0.4kB/s. For this test,I used SMP server app and did the compilation...
