Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hello,
I'm getting started with nRF Connect SDK. I've installed the toolchain and SEGGER through Getting Started App (because for some reason the Toolchain Manager froze...
Good day,
I have done DFU using the secure bootloader example in sdk16 using the nrf connect app. The DFU process completes successfully and the controller runs the new...
Good evening, I'm looking for a Blue Tooth BLE Low Energy for Low Power application.
This application should consume few mA only when the controller will be in TX and so...
Hi,
Could I get clarification on if the USB peripheral is isolated and won't backfeed?
In my product, VDDH & VDD are powered via a DC adapter that can be unplugged while...
Hello,
I continue to deal with Zigbee and I have another question. I use 2 nRF52840 chips. First nRF as a Zigbee Coordinator (CLI in SDK\examples\zigbee\experimental\cli...
Hi Team,
We are planning for use the NRF52832 Module for our development, In that for Secure data storage exchange we are implemented the some of the crypto mechanisms...
Hello,
When operating the Thingy91 in poor network connectivity environments, the call to getaddrinfo will sometimes block and eventually timeout returning a error code...
Hello,
I am using the nRF52840_DevKit and SDK-v16.0.0. I am planning to build and flash a bootloader with NRF_BL_DEBUG_PORT_DISABLE set to 1, which means APPROTECT and...
Hi,
I'm using SES v4.52b, a nRF52832 module (BL652) and nRF5 SDK 16.0.0. I'm trying to build a generic SPI Read and Write functions with the following:
The device I...
Hi there,
I am in the process of developing a custom PCB using the nRF52833 SoC. This board is quite simple, and doesn't use many of the pins of the nRF52833 SoC.
I am...
nRF5_SDK_16.0.0_98a08e2\examples\peripheral\uart. In the SDK 16 ,UART example,why the legacy driver nrf_drv_uart.c is used instead of the sdk recommended nrfx_uart.c.
Secondly...
hello,
I'm using SDK 16.0 with nrf52832, for storing some information iam using flash storage, during initialization, we are giving a starting and ending address to flash...
Hi friend,
We have a project with BLE connection. It sends out the Manchester data and the data modulates with 125KHz. Can we use PWM to do that? Will the data format be...
My platform is SDK16 with softdevice, MCU nRF52840. I used 2 pin to generate PWM at 125KHz for Manchester coding. I want them are at different pin polarity. For example, if...
Hi all,
I am working with the nRF52 dev kit and the ecg sensor MAX30003. Using MBED to develop firmware.
I am using this library and the example code from maxim ( https...
